manualshive.com logo in svg

Seneca S6001-RTU, Руководство пользователя


Поделиться
Скачать
background image

USER MANUAL – Z-TWS4/Z-PASS2-S/S6001-RTU 

 
 

 

 

196 

 

 

 

19.1.21

 

SET_ALARMS_STAT 

 

This FB sets the value of the "status" field for the alarm records specified by 
the passed arguments. 
 
INPUTS: 
- STATUS : this parameter is handled as a bitmask, meaning that the status of 
the relevant alarm records will be set as: 
  alarms.stat = (alarms.stat | STATUS), where: 
  alarms.stat: DB field 
  STATUS: this parameter 
- FIRST_ID : the id of the first record retrieved by the GET_ALARMS FB 
- LAST_ID : the id of the last record retrieved by the GET_ALARMS FB 
- @ENABLE: TRUE  -> FB is executed 
           FALSE -> FB is skipped 
           the parameter is set to FALSE by the FB at the end of execution 
 
OUTPUTS: 
- RESULT: the FB result; possible values are: 
   0: FB still running 
   1: FB successfully executed 
  -1: FB execution failed 
  -2: FB execution timeout 

Содержание S6001-RTU



















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S6001-RTU

zipwake S Series Troubleshooting Manual preview
S Series
Бренд: zipwake Страницы: 12
Watts 7 Series Installation, Maintenance & Repair preview
7 Series
Бренд: Watts Страницы: 2
jbc UCR Instruction Manual preview
UCR
Бренд: jbc Страницы: 12
Faulhaber MC 5004 Technical Manual preview
MC 5004
Бренд: Faulhaber Страницы: 66
M-Audio Axiom AIR 25 Service Manual preview
Axiom AIR 25
Бренд: M-Audio Страницы: 26
M Climate Bobbie Installation Instructions Manual preview
Bobbie
Бренд: M Climate Страницы: 12
SAI HVAC Compact Comfort VAV12 User Manual preview
Compact Comfort VAV12
Бренд: SAI HVAC Страницы: 16
Saitek Pacific AV8R Manual preview
Pacific AV8R
Бренд: Saitek Страницы: 15
saia-burgess PCD3 Series Hardware Manual preview
PCD3 Series
Бренд: saia-burgess Страницы: 203
Sailor N420 Technical Manual preview
N420
Бренд: Sailor Страницы: 1
Samson 3372 User Manual preview
3372
Бренд: Samson Страницы: 8
Samson 3249 Mounting And Operating Instructions preview
3249
Бренд: Samson Страницы: 60
Samson 2405 Series Mounting And Operating Instruction preview
2405 Series
Бренд: Samson Страницы: 40
Watts 009 Series Operation, Installation, Maintenance And Repair Manual preview
009 Series
Бренд: Watts Страницы: 8
Keba Kemro K2 Project Engineering Manual preview
Kemro K2
Бренд: Keba Страницы: 16
KEB COMBIVERT F5 Safety Manual preview
COMBIVERT F5
Бренд: KEB Страницы: 16
fadini ZERO.SAPE Manual preview
ZERO.SAPE
Бренд: fadini Страницы: 28
GEA VESTA Operating Instructions Manual preview
VESTA
Бренд: GEA Страницы: 47

Бренды по названию

Популярные бренды

Загрузить еще бренды