manualshive.com logo in svg

Sencore VB330, Руководство пользователя

Поделиться
Скачать
Sencore VB330 Скачать руководство пользователя страница 94

6.7

Traffic

6.7.1

Traffic — Protocols

The

Protocols

view allows monitoring of IP traffic on the selected port in terms of the protocols used.

The interface can be selected using the drop-down at the bottom of the page. Clicking the

Clear statistics

button will reset displayed values.

The following measurements are presented, depending on which statistic is selected:

Statistics

Statistic:

The protocol for which the following measurements apply

Cur bitrate:

The current total bitrate for this protocol (measured over the last 1s period)

Max bitrate:

The maximum bitrate during any 1s period

Min bitrate:

The minimum non-zero bitrate during any 1s period

Frames/sec:

Traffic speed in number of IP packets per second

Frames:

Number of Ethernet frames

Frames %:

Percentage of total number of frames

Min flen:

Minimum Ethernet frame length

Max flen:

Maximum Ethernet frame length

Bitrates

Statistic:

As above

Cur bitrate:

As above

Bitrates:

A graph displaying the bitrate over time, displaying the last five minutes

94

VB3xx 10G Probe User’s Manual version 5.3

Содержание VB330












































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды