SENAO OAP7250AG Скачать руководство пользователя страница 1

 

      

                  

Quick Installation Guide 

OAP7250AG 

Wireless 450M + 1.3Gbps Long Range outdoor Dual Band Concurrent 
AP 

 

Please verify contents of the box before continuing to set up the OAP7250AG. 

 

OAP7250AG Access Point 

 

OAP7250AG Quick Start Guide 

 

Mounting Bracket 

 

PoE injector 

 

Mounting Kit Package (includes hex cap screws, washers, wall anchors and bolts, ring clamp) 

 

Ground Cables 

 

Packaged Ground Screw 

 

Power Adapter 

 

Pole Mounting Bracket 

 

7dBi 5GHz Omni-directional antennas 

 

5dBi 2.4GHz Omni-directional antennas 

 

 

Connect to the OAP7250AG Access Point 

1.

 

Attach and gently tighten the provided antennas to the appropriate port on the OAP7250AG 

2.

 

Attach one of the supplied Ground Cables to the Ground screw on the PoE injector. 

3.

 

Attach the wire end the Ground Cable to a safety ground. 

4.

 

Using one of the CAT5e/CAT6 Ethernet cable, connect one end of the cable to the LAN1 Port (PoE 
Input) of the CAP7250AG and the other end into the AP/Bridge port on the PoE injector. 

5.

 

Connect the second CAT5e/CAT6 Ethernet cable to the Switch/Computer Ethernet port. 

6.

 

Connect the Power adapter to the DC IN port of the PoE injector and plug the other end into an 
electrical outlet. 

 

Содержание OAP7250AG










Отзывы: