Step 2. HANGING THE SHADE
No-Headrail
Once the brackets are secured and level, the fabric roll can be
inserted. Make sure your hands are clean to avoid soiling the fabric.
While facing the inside of the shade, be
sure the clutch and roller end plug are
inserted into the roller. Hold the shade with
the bottom of the clutch facing the floor, and
the beaded cord hanging straight down.
Insert the foot of the control-
side bracket into the slotted
center hole of the clutch. Set
nub of the end plug into the V
of the support bracket.
Rotate the T-hook on the
support bracket to engage
over the nub on the idler and
secure the fabric roll.
Headrail
Ultra Sleek & Ultra Sleek Plus
Deluxe Rail
Headrail Removal
To remove the shading, partially lower the shading and insert a flat
head screwdriver as shown. Twist the screwdriver until the headrail
disengages from the bracket.
Fully Recessed Inside Mount (Deluxe Bracket Only)
Outside Mount
Extension Brackets
(optional for headrail shades)
Optional Extension Brackets are used to project the back of the
shading up to 2 1/2" from the mounting surface. Attach the Ultra
Sleek or Deluxe Mounting Bracket to the Extension Bracket with the
nut and bolt provided.
Side Mount
(optional for headrail shades)
Measure from window sill up to desired mounting position on each
side of the window frame. Mark position. Mount Side Mount
Brackets on each side of window frame as shown. Make sure to
confirm that headrail will sit perfectly level. Once Side Mount
Brackets are installed and properly positioned, attach the Ultra Sleek
or Deluxe Mounting Brackets using the nuts and bolts provided.
BASICS
Please take a moment to identify which headrail version you have and then follow
the appropriate instructions.
A few simple tools are required:
- Measuring tape
- Carpenters Level
- Power drill or Phillips head Screwdriver
- ¼" Hex head and/or Phillips driver bit
Additional fasteners other than those sent with your shading may be
required depending on the mounting surface. Wallboard and plaster
require the use of anchors such as expansion or toggle bolts. Brick,
tile or stone need special plugs and drill bits. Remember to always
pre-drill holes in wood to avoid splitting.
Step 1. BRACKET INSTALLATION
Inside Mount
Hold Down Bracket
and screw
(optional)
If the headrail does not sit level, the fabric will not roll up
evenly which could damage the edges of the shading
fabric. Use shims if necessary to level brackets.
Low light gap wedges can be used to
reduce the top light gap when the shade is
mounted fully recessed. The wedge is
placed between the mounting surface and
the bracket with the tabs on the wedge
facing down and the thick end of the
wedge toward the back of the bracket.
3/4” minimum surface
2” minimum surface required
Position screw in center of slot
so you can adjust position of
bracket as necessary.
Push the rail back until
it is fully engaged.
Push the rail back until
it is fully engaged.
Deluxe
Ultra Sleek &
Ultra Sleek Plus
2 1/2”
2 1/2”
3/4” minimum surface
Ultra Sleek &
Ultra Sleek Plus
Deluxe
Ultra Sleek &
Ultra Sleek Plus
Deluxe
Deluxe
3/4” minimum for shallow
mount
Minimum for flush inside mount
Ultra Sleek 3”
Ultra Sleek Plus 3 3/4”
Deluxe 3 3/4”
Use shims if necessary to ensure that the headrail is mounted level (included).
2”
2”
Ultra Sleek &
Ultra Sleek Plus
Deluxe
1 1/4” Hex
Head
Bracket
Screw
Deluxe
Mounting
Bracket
Wedge for Deluxe
Headrail Bracket
Headrail Extension &
Side mount Bracket
Nut &
Bolt
“U” Shim for
Headrail bracket
Roller Mounting
Brackets for NO Headrail
Ultra Sleek &
Ultra Sleek Plus
Mounting
Bracket
Control Side
Bracket
End Plug Side
Bracket
Foot
T-Hook
No-Headrail
Shade width # of Brackets
Up to 40”
2
>40” - 72”
3
>72” - 84”
4
>84” - 114”
5
No-Headrail
Nub
Support Bracket
Fig.15
Ultra Sleek &
Ultra Sleek Plus
1 1/2” minimum
1 1/2” minimum surface
