SelectBlinds Fashion Color Power Touch Series страница 5 Скачать руководство пользователя

Страница: 5 / 31

Press the

DOWN

button to lower or raise the shade. Press the

STOP/

FAVORITE

to stop the shade at the desired position.

To fully raise or lower the shade, simply press the

DOWN

button and

then release. The shade will automatically stop when it reaches the upper or

lower limit.

(If the upper or lower limits are not set at the desired positions, see

the Adjust Motor Limits section on the next page)

Note: Upper and lower limits stops are set at the factory. An intermediate, or

“favorite” position is not set at the factory. See page 6 for more information.

OPERATION

Down

Stop/Favorite

Insert the foot of the motor-side bracket into the slotted center

hole of the motor end of the fabric roll.

Set the post of the idler end into the V of the support bracket.

Rotate the T-hook on the support bracket to lock in the post

and secure the fabric roll.

Bundle excess wire and secure with the cable tie mounting

base and cable ties.

Nub

Support Bracket

Fig.15

Idler Post

V slot

SHADES WITH NO HEAD RAIL

Содержание Fashion Color Power Touch Series
































Результаты поиска

Содержание Fashion Color Power Touch Series

Отзывы:

Похожие инструкции для Fashion Color Power Touch Series

Бренды по названию

Популярные бренды

SelectBlinds Fashion Color Power Touch Series, Инструкции по установке и уходу

Результаты поиска

Содержание Fashion Color Power Touch Series

Отзывы:

Похожие инструкции для Fashion Color Power Touch Series

Бренды по названию

Популярные бренды