Doc. name: OP INST RPS240-24-CE OP891-V02(Page 1 of 2)
WIRING INSTRUCTIONS
1. To prevent risk of electric shock, power supply equipment must be
kept OFF while wiring.
2. Terminals and electrically charged parts must not be touched when
the power is ON.
3. Wiring shall be done strictly according to terminal layout provided
in the operating manual.
50*136*135mm (W*H*D)
645 gms
DIMENSIONAL DIAGRAM
DIMENSION
WEIGHT
OP891-V02
PROTECTIONS
OUTPUT OVER VOLTAGE
OVER TEMPERATURE
110% to 140% of rated output current
Protection type : Hiccup mode; recovers
automatically after fault condition is removed.
31VDC
Protection type :
± 0.5VDC
Latched; Input AC power
has to be recycled to recover the power supply.
Power supply shuts down when the temperature of PCB
below PFC choke reaches typically 120 C; Recovers
automatically when temperature falls to typically 90 C.
0
0
4A - 250VAC Internal
Hiccup mode when output is shorted; Recovers
automatically after fault condition is removed.
INPUT FUSED
OUTPUT SHORT CIRCUIT
OUTPUT OVER LOAD
Ø
Ø
Ø
Ø
Ø
Ø
AC 100-240V Wide-range Input.
Active PFC
Cost optimized without compromising quality or reliability.
Full power between -25 C and +50
.
DC-OK Relay contact.
Compact size.
0
0
C
FEATURES
SPECIFICATION
RPS240-24-CE
Operating Instruction
selec
WIRING DIAGRAM
50
136
135
5
INTENDED USE
This device is designed for installation in an enclosure and is intended for the
general professional use such as in
ndustrial control
communication .
Do not use this power supply in equipment where malfunction may cause
severe personal injury or threaten human life.
instrumentation equipment, office,
i
and
SAFETY INSTRUCTION
PE (Protective
Earth) Input
OUTPUT SPECIFICATIONS
≥
≥
25ms at 24V & 16ms at 28V @ 115/230VAC, Full Load
HOLD UP TIME
24 - 28VDC
<1% of Vout
10A at 24V; 8.6A at 28V
OUTPUT VOLTAGE
OUTPUT CURRENT
RIPPLE AND NOISE
LINE AND LOAD REGULATION
±1%
Possible for up to two power supplies
(with external diode)
*
DC-OK CONTACT
SERIES OPERATION
30VDC 1A; 60VDC 0.5A; 125VAC 0.5A,
resistive load; min. current 1mA
24VDC 10A
OUTPUT
L N
DC ON
DC ON
Vo ADJ.
DC OK
DC OK
+
-
-
+
100 - 240VAC
; 50/60Hz
100 - 240VAC
; 50/60Hz
INPUT
INPUT
RPS240-24-CE
240W
ENVIRONMENT
STORAGE TEMPERATURE
ALTITUDE
-40 C to +85 C.
0
0
2000m
-25 C to +70 C
*De-rate output power at 6W/ C above +50 C Ambient.
0
0
0
0
5 to 95% RH, Non Condensing
OPERATING TEMPERATURE
HUMIDITY
CURRENT HARMONICS
Class D
EMS IMMUNITY
Compliance to IEC61000-4-4,5,11
EN55022 ; Class A
RADIATED EMISSION
EN55022 ; Class B
CONDUCTED EMISSION
SAFETY & EMC
DIELECTRIC WITHSTAND
VOLTAGE
I/P to Earth : 2500VAC
I/P to O/P
: 4000VAC
O/P to Earth
: 1500VAC
O/P to DC-OK : 500VAC
Designed to meet IEC 62368-1
Processing for UL-508
SAFETY STANDARDS
100 M min. (between all outputs and all inputs
terminals) at 500 VDC
/
PE
INSULATION RESISTANCE
Ω
INPUT SPECIFICATIONS
100 - 240VAC
INPUT VOLTAGE RANGE
START UP TIME
AC CURRENT(TYP.)
2.4A @ 115VAC; 1.2A @ 230VAC
EFFICIENCY(TYP.)
93% @ 230VAC
INRUSH CURRENT(TYP.)
<60Amps; Measured at 264VAC,
25 C Ambient, Cold Start
0
POWER FACTOR
>0.95 @ Full Load Over entire input range
2 Sec @ Full Load Over entire input range
FREQUENCY RANGE
50-60Hz
±10% ; 127 - 370VDC
<
