DIGITAL ACTIVE INFRARED SENSOR
38mm
~
50mm
INSTRUCTION MANUAL
SUGGESTIONS FOR INSTALLATION
1
2
1
PARTS DESCRIPTION
SUGGESTIONS FOR INSTALLATION
2
3
4
INSTALLATION
WALL
MOUNT
Each bracket to be reversely attached.
1. Pull the wire through the
wire hole of the pole.
2. Attach the bracket to the pole with the pole holder.
POLE MOUNT
Pole mount back-to-back
Ensure the sensors line of sight is
free from any false alarm sources
such as bushes, trees, etc. ( Pay
attention to these as they may
change seasonally.)
Ensure strong sunlight or car
recommended.)
headlights do not shine directly
from the optical axis is not
on to the receiver. (Within
2
Direction of installation
Horizontally 180
Vertically 20
Because angle of reflection mirror is adjustable
unit can be installed in various directions.
in 90
horizontally and 10
vertically, the
In case of jump phenomenon, as shown
of transmitter and receiver to the following
section in the above, change the disposition
manner shown s ection.
COVER
MAIN BODY
Connection
Terminal
LED
Wire Hole
Monitor Jack
(Only for Receiver)
Obscuration Time
Adjustment
(Only for Receiver)
4
Frequency Channel
Switch
Tamper
Horizontal Angle
Adjustment Dial
Viewfinder
Cover Lock
Screw
LENS
Vertical
Adjustment
Screw
LED
GOOD ( Green )
POWER ( Green )
:on when optically aligned : on when the transmitter is working
:off when optically not aligned
LEVEL ( Red )
:on when Alarm is activated in accordance with Alarm LED ( Red )
ALARM ( Red )
:on when Alarm is activated in accordance with LEVEL ( Red )
RECEIVER
TRANSMITTER
Monitor jack : Should be used for making the optimum optical axis adjustment
( Refer to
'
how to use the monitor jack'
)
Obscuration time adjustment : To be used for setting the obscuration time
( Refer to
'
adjustment of obscuration time '
)
Ensure the sensors are
mounted on a stable and
firm fixing.
Note that here the protection
distances refers to the sheet
below.
Height of installation and
protection distance
Receiver
Transmitter
Receiver
Transmitter
Receiver
Transmitter Transmitter
Receiver
Bracket
Pole holder
Pole cover
1. Loosen screw holding cover and
remove the cover.
2. Attach the mounting pattern paper
to the wall, mark the installation
holes, and make guide holes.
3. Break knock-out and pull wire
through.
5. Connect wires to the terminal.
( Refer to the Terminal Configuration
right hand side )
6. Make the optimum optical adjustment as per
section 5 and confirm system operation before
replacing covers.
Wiring distance
POWER
ALARM
TAMPER
RECEIVER
TAMPER
TRANSMITTER
POWER
FREE
TERMINAL CONFIGURATION
4. Pull wire through, install SBM
onto flange and the wall.
knock-out
Protection Distance
Spread
of
Beam
0.7
~
1.0m
14mm
33mm
33mm
GOOD LEVEL ALARM
POWER
1 2 3 4 5 6 7
1 2 3 4 5 6 7
SBT-100F
SBT-150F
SBT-80F
SBT-60F
SBT-30F
SBT-40F
SBT-30F
SBT-100F
SBT-80F
SBT-150F
30m
80m
100m
150m
4.5m
3.0m
2.4m
0.9m
SBT-60F
60m
1.8m
SBT-40F
40m
1.2m
Spread of
Beam
Protection
Distance
Model
Model
Voltage
Wire
diameter
SBT-30F
SBT-40F
SBT-60F
SBT-80/100F
24V
12V
24V
12V
24V
12V
24V
2
¦Õ
2
¦Õ
2
¦Õ
2
¦Õ
12V
0.3mm ( 0.6)
0.5mm ( 0.8)
0.75mm ( 1.0)
1.25mm ( 1.2)
12V
24V
SBT-150F
2143m
3750m
5000m
7500m
238m
833m
556m
417m
2143m
3750m
5000m
7500m
238m
833m
556m
417m
2143m
3750m
5000m
7500m
238m
833m
556m
417m
2143m
3750m
5000m
7500m
238m
833m
556m
417m
2143m
3750m
5000m
7500m
238m
833m
556m
417m
