background image

0000136864 

rev. 4.2 

1

POOL BASIC evo 

 

WARNINGS 

!

IMPORTANT!

 

 

Before carrying out ANY work inside control panel of the Pool Basic Evo device, make sure you disconnect it 

from the power supply. 

 

FAILURE TO COMPLY WITH THE INSTRUCTIONS CONTAINED IN THIS MANUAL COULD CAUSE INJURY TO 
PEOPLE AND/OR DAMAGE TO THE APPLIANCE AND THE SYSTEM.
 

 
PACK CONTENTS

 

 

 

A) "Pool Basic" pH control device (standard model) 
B) PVC Cristal 4x6 suction hose (4 m)  
C) Polyethylene delivery hose (5 m) 
D) Attachment screw (

φ

=6 mm)  

E) Foot filter (PVC riser) 
F) FPM duckbill valve (3/8” GAS) 
G) SPH-1 pH electrode 
H) PSS3 probe-socket (1/2” GAS) 
I)  Tapping  saddle  for  securing  PSS3  onto  2”  hose 
(

φ

=50 mm) 

L) pH 4, pH 7, H

2

O buffer solution kit 

M) Reducer for injection valve 

 
 
 

 

The pH probe is a product subject to wear and tear and is therefore not covered by the warranty.  

 

Chemical products

 

Recommended for lowering pH => negative pH (with a sulphuric acid base) 

 

Recommended for raising pH => positive pH (sodium carbonate or bicarbonate) 

 

 

ABSOLUTELY not recommended => pure sulphuric acid 

 

Note:   These products are DANGEROUS (I A) and require special precautions during use, handling and storage.

 

 

 

Pool Basic Evo was designed to regulate the pH of tanks up to 90 m

3

. 

B

 

NEVER mix chemical products. 

B

 

NEVER allow children or people who have not read this manual to use or tamper with Pool Basic Evo or any of 
its peripheral components (including chemical products). 

 

 

TECHNICAL SPECIFICATIONS 

 

Dimensions (H – W – L) 

 

234x162x108 mm          Maximum back-pressure   1,5 bar 

Weight   

 

 

 

1 kg       

 

Pump state 

Pause - Supply 

Power supply 50 Hz 

 

 

230 VAC  

 

pH scale 

6.2 pH – 8.0 pH 

Consumption   

 

 

7 W o 12,5 W     

pH control range 

  0.0 pH – 14.0 pH 

Pump flow rate   

 

 

1,5 l/h; 5 l/h      

Device precision 

+/- 0.02 pH 

Electrode regulation 

 

 

Automatic 

 

Wall Mounting Setup 
 
 
 
 
 

 
 
 
 
 

 

Make sure that the injection pressure is below 1.5 bar.

 

 

Содержание PoolBasic EVO

Страница 1: ...ered by the warranty Chemical products Recommended for lowering pH negative pH with a sulphuric acid base Recommended for raising pH positive pH sodium carbonate or bicarbonate ABSOLUTELY not recommended pure sulphuric acid Note These products are DANGEROUS I A and require special precautions during use handling and storage Pool Basic Evo was designed to regulate the pH of tanks up to 90 m 3 B NEV...

Страница 2: ...red cable to the auxiliary contact of the filter box 230 Vca Set Point adjustment Keep the key pressed down and set the desired value using the and keys Adjustment Setup Press the and keys simultaneously for 5 seconds to enter the SETUP programme Acid enables you to dose an acid product negative pH Alka enables you to dose an alkaline product positive pH Set using the key Press the key twice to pr...

Страница 3: ...ing 1 minute Quality Probe Wash Keep probe into Buffer solution Press Enter Key and calibrate second point 4 pH buffer solution Please Wait during 1 minute Quality Probe Wash Press Enter Key to save and exit Normal Status Note If you have setting EASY CAL the calibration function has 1 point calibrate only 7 pH buffer solution ...

Страница 4: ... 4 consecutive dosing cycles in which the set level was not reached to return to normal operation press the button the device resets the alarms and returns to normal measuring and dosing mode Flow presence of incoming flow enslavement by the filter pump Alarm Leds Relay Actions to do Level Alarm led Flashing Hold led light ON Alarm Relay Close Push Key to open Alarm Relay Restore Product tank Out ...

Отзывы: