manualshive.com logo in svg

Seizmik 50-50222KIT, Руководство по установке и эксплуатации, Страница: 6 / 12

Поделиться
Скачать
Seizmik 50-50222KIT Скачать руководство пользователя страница 6

There is a gap for the Shim to be snapped in place 

over the M6x50mm Button Head Bolt in between the 

End Mounting Block and the Ball Bracket. Insert the 

shims in this gap in each side by snapping in from 

the bottom side of the windshield. Now, working from 

the middle out, tighten all bolts along the tube 

assembly except the middle bolt of the Brace 

Mounting Block

Remove the two M8 ball studs from each Gas Spring. 

There will be 4 total ball studs. Do this by prying up 

the metal retaining clip with a small flat blade 

screwdriver and pulling the ball stud out. Once the ball 

stud has been removed make sure the retaining clip is 

back in place.

9

10

Install one Ball Stud onto each Ball Bracket using an 
M8 Nylon Insert Lock Nut. Orient the Ball to face 
inwards towards the middle of the windshield, and 
fully tighten using 12mm and 13mm open end 
wrenches.

11

6

Install the T Handle onto the cylinder with the 
M8x30mm Socket Head Bolt. You will need a 6mm 
hex key.

12

8

Содержание 50-50222KIT













Отзывы:

Нет отзывов