background image

PARTS  LIST / TECHNICAL GUIDE

ANALOGUE SOLAR Cal. V172A/V174A

[SPECIFICATIONS]

1/24

Item

Cal. No.

V172A/V174A

Power reserve

Driving system

Additional function

Crown operation

Loss/Gain

Regulation system

Number of jewels

Normal position

1st click position

Current consumption

Gate time for rate measurement

Power 

supply

Motion of the second hand

Coil resistance

Power generator

Rechargeable battery

Operating voltage range

2nd click position

One-second intervals

Stepping motor 4 pieces

Diameter:  Outside 27.6 mm
 

 Casing 27.0 mm

Height:  

4.4 mm

3 hands 

(hour, minute and small 

second hands)

Energy depletion forewarning function (The second hand moves at two-

second intervals.)

Overcharge prevention function

Electronic circuit reset function

Second hand stop function

Date calendar

Instant setting device for date calendar

System reset function

Stopwatch function..........60-minute stopwatch in 1/5-second increments 

        

(Auto stop measuring at 60 minutes)

        

Accumulated elapsed time measurement

        

Split time measurement

        

Single-time alarm function 

        

Stopwatch hand position adjustment

Stopwatch

Time setting, System reset, Setting “0” of stopwatch hand

Monthly rate:less than 15 seconds (worn on the wrist at temperature range 

between 5 to 35 degrees Centigrade)

Use 10-second gate

Nil

Solar power generation system

Movement: less than 0.80 μA

Circuit block: less than 0.40 μA

4002 541  

1.90 - 2.30 k

Ω

 

  (COIL BLOCK) (COIL BLOCK FOR STOPWATCH SECOND) 

4002 542  

1.75 - 2.15 k

Ω

 

  (COIL BLOCK FOR STOPWATCH MINUTE) (COIL BLOCK FOR ALARM)

MT920 Manganese titanium lithium rechargeable battery

0.90V - 2.10V

From full charge to stoppage: Approximately 6 months

Nil

V172A

V174A

Date setting(counter clockwise), Time setting of alarm

3 hands 

(hour, minute and small second 

hands), 24-hour indicator

Содержание V172A


























Отзывы: