manualshive.com logo in svg

Seiko SII RP-D10 Series, Руководство пользователя, Страница: 9 / 46

Поделиться
Скачать
Seiko SII RP-D10 Series Скачать руководство пользователя страница 9

5 

3.  OPERATING PRECAUTIONS 

Be careful of the following precautions and use the products properly in order to deliver and maintain the 

full performance of the products. 

 

 Using the Products 

◆

 

Be careful not to drop or bump the products on a hard surface. 

◆

 

DO NOT install the products in direct sunlight. 

◆

 

Be careful about the ambient temperature and humidity. 

Suitable environment for the use of the printer is as follows: 

•

  Range of the temperature: 5°C to 45°C (41°F to 113°F) 

•

  Range of the humidity: 10%RH to 90%RH 

Refer to "RP-D10 SERIES THERMAL PRINTER TECHNICAL REFERENCE" for the certifiable 

humidity range at each temperature. 

◆

 

DO NOT install the products near devices that generate strong electromagnetic fields such as a 

copy machine motor. 

◆

 

DO NOT install the products in a location that is subject to corrosive gas, siloxane and so on. 

◆

 

DO NOT connect the AC adapter or the AC cable to the same outlet with devices that generate 

noise. 

◆

 

DO NOT open the paper cover during printing or cutting. 

◆

 

DO NOT connect or disconnect the interface cable during printing or transmission. DO NOT touch 

the plug of the interface cable during printing. 

◆

 

Turn off the printer when not in use. 

In addition, when the printer is not used for a long time, unplug the AC plug from an outlet, and set 

thermal paper to protect the platen. 

◆

 

Clean the products' case using soft, lint-free cloth. DO NOT use alcohol or other solvent. 

◆

 

Before using, always clean the terminals using a dry, soft and lint-free cloth. When the terminals are 

dirty, it may cause contact failure. 

◆

 

DO NOT touch the thermal head directly. Doing so may result in poor quality due to the dirt or 

damage by the static electricity. 

◆

 

DO NOT use the thermal head when it is wet. Doing so may damage the printer. 

◆

 

When cleaning the thermal head, wipe the thermal head with a cotton swab or other soft material. 

◆

 

The AC adapter may get hot when in use. This is normal and is not a malfunction. 

◆

 

Using the printer under low temperature environment or printing at a high print rate might cause 

unclear printing or generate loud sound. This is not a failure in the printer, but an inherent paper 

phenomenon. 

◆

 

When handling the printer, be aware of static electricity. When the static electricity is discharged, 

this could cause a USB communication failure. When this problem occurs, disconnect the USB plug 

that is connected to the host device and wait a few seconds before connecting it again. 

◆

 

DO NOT print without the thermal paper. 

 

Содержание SII RP-D10 Series















































Отзывы:

Нет отзывов