manualshive.com logo in svg

Seiko SII RP-D10 Series, Руководство пользователя, Страница: 24 / 46

Поделиться
Скачать
Seiko SII RP-D10 Series Скачать руководство пользователя страница 24

20 

9.  PREVENTION AND TREATMENT OF PAPER JAM 

Do not touch the thermal paper while the paper is being ejected or before it is cut. Covering the paper 

outlet or pulling out the thermal paper during paper ejection may cause a paper jam, cut failure, or line 

feed failure. Never open the paper cover during paper cutting. 

 

 
 

 Removing Paper Jam 

When a paper jam occurs, remove the thermal paper according to the following procedure. 

 

(1)  Turn off the printer. 

(2)  Operate the release lever to open the paper cover, and remove the paper jam. 

NOTE 

◆

 

Do not damage the printer when removing the thermal paper. 
Especially, do not touch the thermal head because it is easy to break. 

 

(3)  Set the thermal paper straight and then close the paper cover gently. 

(4)  Turn on the printer. 

(5)  When the printer is recovered, the LED lights in green. 

NOTE 

◆

 

DO NOT touch the thermal head immediately after printing because it may get hot. 

 

 

 

Do not touch during operation.

Содержание SII RP-D10 Series















































Отзывы:

Нет отзывов