Seiko MPU-L465 Series Скачать руководство пользователя страница 5

Страница: 5 / 55

- 2 -

SAFETY PRECAUTIONS

The following symbols are used in this manual in order to make proper use of the printer and avoid

incidental damages.

Follow the guidelines marked with each individual symbol.

WARNING

Failure to follow the guidelines marked with this symbol

could result in serious personal injury or death.

CAUTION

Failure to follow the guidelines marked with this symbol

could result in minor personal injury or product and/or

peripheral damage.

Symbol Examples

The symbol

indicates caution (including danger and warning).

This example indicates warning or caution.

The symbol

indicates prohibition.

This example indicates prohibition of disassembling.

The symbol

indicates requirements or what must be done.

This example asks you to unplug the power cable.

Содержание MPU-L465 Series
























































Результаты поиска

Содержание MPU-L465 Series

Отзывы:

Похожие инструкции для MPU-L465 Series

Бренды по названию

Популярные бренды

Seiko MPU-L465 Series, Руководство пользователя

Результаты поиска

Содержание MPU-L465 Series

Отзывы:

Похожие инструкции для MPU-L465 Series

Бренды по названию

Популярные бренды