Seiko MPU-L465 Series Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 55

background image

-

33

-

7. FUNCTION SETTINGS

The printer allows for numerous function settings according to the operating conditions and

applications.

The settings are saved in the software DIP switches (non-volatile memory) mounted on the printer. The

setting can be controlled by the buttons or commands.

The following describes how to set functions by using buttons.

Hint



See the

MPU-L465

Technical Reference

for details on function settings with

commands.

■

Function Setting Mode

The printer must be in the function setting mode to set functions with buttons.

Follow steps (1) through (3) to enter the function setting mode:

(1) Make sure that the paper is loaded and the printer is off. If the paper is not loaded, load the paper as

described in Section 4, Paper Setup, and then turn the printer off.

Hint



If an error occurs in the function setting mode, the POWER lamp blinks several times

and then the power is turned off.

(2) Press the POWER and REPRINT buttons simultaneously. When the POWER lamp lights, release

the POWER button, then the REPRINT button.

(3) If the message shown below is printed, press the FEED button.

Select Function

Setting Mode: FEED SW

HEX Dump Mode: REPRINT SW

Hint



If you press the REPRINT button at this time, the printer enters the HEX Dump mode.

This mode enables you to see the printer's transmission status. See the

MPU-L465

Technical Reference

for details.

«
...
34
35
36
37
38
...
»

Содержание MPU-L465 Series
























































Отзывы:

Нет отзывов

Похожие инструкции для MPU-L465 Series

Бренд: m3d Страницы: 23

Бренд: m3d Страницы: 26

Бренд: Unisys Страницы: 255

Бренд: Xerox Страницы: 199

Бренд: Oki Страницы: 100

Бренд: Oki Страницы: 2

Бренд: Xerox Страницы: 316

Бренд: Xerox Страницы: 74

Бренд: Xerox Страницы: 306

Бренд: Xerox Страницы: 16

Бренд: Xerox Страницы: 4

Бренд: Oki Страницы: 38

Бренд: Oki Страницы: 38

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 2

Бренд: Ricoh Страницы: 126

Бренд: Edimax Страницы: 93

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды