Seiko LTP1245R-C384-E Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 74

Seiko LTP1245R-C384-E Скачать руководство пользователя страница 9

1-1

1

PRECAUTIONS

Read through this manual to use the printer properly.
Also, design the product taking the detailed precautions that are noted in each section into consideration.

This reference manual subjects to change without notice.
Ask the latest information of the printer to our service.

Damage due to improper handing of the printer without following the instruction described in this
reference manual will not be responsible for SII.

To use the printer safely, design the product taking the precautions described below into
consideration.
Also, attach the safety precautions to all of user's manuals to further inform the users
concerning usage safety.

1.1 SAFETY PRECAUTIONS

To use the printer safely, design the product taking the precautions described below into consideration.
Also, attach the safety precautions to all of user’s manuals, as well as place warning labels on the products
to further inform the users concerning usage safety.

Precautions to prevent the thermal head from overheating

If the thermal head heat element, which always has electricity supplied by the CPU,
malfunctions, the thermal head may overheat, causing smoke and fire.
To prevent personal injury, the printer should be controlled so that the detection of abnormal
temperatures of the thermal head is performed as described in

Section 3.6.9

.

Turn printer off immediately if abnormal conditions occur.

Precautions on temperature of the thermal head when handling

Design the outer case to prevent the user from being burnt by touching the thermal head and its
periphery directly due to the fact that the thermal head and its periphery are hot when printing
and remains so immediately after printing. Regarding paper insertion and head cleaning,
prepare caution descriptions in the manual stating to perform these operations after the head
temperature drops. To allow cooling, insert clearance between the head and the outer case in
designing the outer case.

Precautions regarding raising the temperatures of the motor

Give warning to prevent the user from being burnt by touching the thermal head directly due to
the fact that the motor is hot when operated and remains so immediately after operating. To
allow cooling, insert clearance between the head and the outer case in designing the outer
case.

Precautions regarding sharp edges of the printer body

The printer body and/or some parts may have some sharp edges. Design the outer case to
prevent the user from being injured by touching said sharp edges and provide warnings
concerning this.

CHAPTER

«
...
7
8
9
10
11
...
»

Содержание LTP1245R-C384-E











































































Отзывы:

Нет отзывов