Seiko LTP1245R-C384-E Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 74

Seiko LTP1245R-C384-E Скачать руководство пользователя страница 43

3-29

3.7.3 Automatic Paper Load

Paper can be automatically loaded when used in conjunction with the paper detector. To prevent paper
from skewing, cut the edges at right angles in line with the paper feed direction before loading it.

If skewed, feed the paper until it is straight, or place the head in the up position and adjust the paper so that
it is fed straight.

Figure 3-13

shows a flowchart for automatically loading paper.

Figure 3-14 Flowchart for Automatic Paper Load

Head down

Paper is present.

Head up

Paper is
exhausted.

Paper is
exhausted.

Paper exists.

CHECK FOR

PAPER

START

CHECK FOR

PAPER

Head up/down

detection

*

Drive the motor in the
normal direction by the
specified number of steps.

END

Stand-by for print operation

*
Drive the motor at lower than the frequency
during automatic paper loading described in
3.3 PAPER FEED CHARACTERISTICS.

Set the number of motor drive steps in
consideration of:

•

Deviation in the force of the rubber roller

to catch the paper

•

Distance to the paper eject

The distance between the paper detector and
the heat elements is approximately 8 mm.

«
...
41
42
43
44
45
...
»

Содержание LTP1245R-C384-E











































































Отзывы:

Нет отзывов