Seiko LTP1245R-C384-E Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 74

Seiko LTP1245R-C384-E Скачать руководство пользователя страница 3

iii

PREFACE

This reference manual describes the specifications and basic operating procedures for the LTP1245 (for
RoHS) Line Thermal Printer Mechanism.

For the LTP1245 (RoHS supporting), four models are available:

•

LTP1245R-C384-E

•

LTP1245S-C384-E

•

LTP1245T-S384-E

•

LTP1245U-S384-E

In this reference manual, the information mentioned as LTP1245 is common to all models

unless otherwise noted, and if the information is different depending on the model, specific

model name is mentioned clearly.

Chapter 1 “Precautions” describes safety, design and operational precautions.  Read it thoroughly before
designing so that you are able to use the LTP1245 properly.

SII has not investigated the intellectual property rights of the sample circuits included in this manual.  Fully
investigate the intellectual property rights of these circuits before using.

Also, when designing the  circuits  based  on  the  sample  circuits  in  this  reference  manual,  use  them  after
thorough verification.

«
1
2
3
4
5
...
»

Содержание LTP1245R-C384-E











































































Отзывы:

Нет отзывов