Seiko LTP1245R-C384-E Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 74

Seiko LTP1245R-C384-E Скачать руководство пользователя страница 12

1-4

Connect or remove the connectors after powering off the printer.

When printing at a high print rate (black or zigzag pattern) in a low temperature or high humidity
environment, the vapor from the paper during printing may cause condensation to form on the
printer or may soil the paper itself.
Keep the thermal head away from water drops.

It may become the source of a corroded thermal head.

If condensed, power off the Vp until dried.

The LTP1245 is not a water-proof printer. Prevent contact with water and do not perform
operations with wet hands. They may become sources of damages to short circuits,
overheating and fire.

The LTP1245 is not a dust-proof printer. Use in a dusty place may cause damage to the
thermal head and cause paper feed problems.

1.2.3 Precautions on Discarding

When discarding used printers, discard them according to disposal regulations and rules of each
respective district.

«
...
10
11
12
13
14
...
»

Содержание LTP1245R-C384-E











































































Отзывы:

Нет отзывов