Thermal Printer
ＤＰＵ−Ｈ２４５ＡＰ−Ａ０３Ａ−Ｅ
ＤＰＵ−Ｈ２４５ＡＳ−Ａ０３Ａ−Ｅ
ＤＰＵ−Ｈ２４５ＡＳ−Ｂ０３Ａ−Ｅ
Instruction Manual
This product complies with EU RoHS Directive(2002/95/EC).
Please refer to the page in Chinese for the information of the hazardous substances under China RoHS
（
Management
Methods for Controlling Pollution by Electronic Information Products
）
.
INTRODUCTION
Thank you very much for your continued favor. Please read this manual attentively to let this equipment serve you for as
long as possible. Keep this manual carefully.
SAFETY PRECAUTIONS
The following symbols are used in this Instruction Manual in order to make use of the printer properly and prevent the
printer from being damaged.
Follow the instructions marked with the symbol.
WARNING
Failure to follow the guidelines marked with this symbol could result in severe
personal injury or death.
CAUTION
Failure to follow the guidelines marked with this symbol could result in minor
personal injury or product and/or peripheral damage.
Symbol Examples
The symbol
indicates caution(including danger and warning).
The example on the left indicates warning or caution.
The symbol
indicates prohibition.
The example on the left means prohibition of disassembling.
The symbol
indicates requirement or what must be done.
The example on the left means “pull the power plug out of the outlet.”
WARNING
DO NOT use any AC adapter,AC cable or battery pack other than those specified.Doing so may cause fire
leading to serious accidents.
DO NOT use the printer and the AC adapter in countries where these items do not comply with the
regulations.
Doing so, we do not assure the safety of these products and you will be responsible for violation of
regulations.
DO NOT bend the power cable forcibly, or place heavy object on the cable because it might damage the
cable and cause fire or electric shock.If the power cable is damaged, discontinue use and replace it
immediately.
Never disassemble the printer, the battery pack, the AC adapter and the AC cable. Failure to follow this
instruction may cause overheating or burning of the printer or the AC adapter, or an electric shock, which
may lead to fires or accidents.
CAUTION
DO NOT drop any metallic objects or liquids, such as water or coffee, into the printer.
Never use the printer in a place of extreme humidity or any place where it can possibly be splashed by any
liquids. If any liquids get into the printer, it could lead to fire, electric shock, or other serious accidents.
Never touch the thermal head immediately after printing because it becomes very hot. Make sure that the
thermal head is cool before setting papers or cleaning the thermal head.
Be sure to hold the connector part of the power cable or interface cable when disconnecting the cable.
Pulling on the cable portion may cause it to fray and break.
POWER OFF the printer, unplug the power cable from the power outlet, and remove the battery pack in
any of the following cases:
◆
The printer does not recover from an error.
◆
Smoke, strange noise or smells erupt from the printer.
◆
A piece of metal or any liquid touches the internal parts or slot of the printer.
Using the printer in any manner other than for which it was designed may cause accidents or fire.
WARNING
DO NOT throw the battery pack into fire and DO NOT heat it.
Doing so may cause explosion or fire leading to fire or injury.
DO NOT put the battery pack into water. Always keep it away from rain and water.
Doing so may cause liquid leakage leading to fire or electric shock.
DO NOT disassemble the battery pack.
Doing so may cause the battery pack to heat up and catch fire, leading to other serious accidents.
DO NOT short the battery pack terminals.
Doing so may lead to fire, electric shock, or personal injury.
DO NOT subject the battery pack to direct sunlight as in a car or high temperature.
Doing so may lead to fire or personal injury.
If any fluid from the battery pack gets in your eyes, immediately flush with water and seek medical
treatment from a trained doctor.
１．
OPERATING PRECAUTIONS
Observe the following for safe and trouble-free operation:
Notes on use
•
Do not drop or hit the printer.
•
Turn off the power switch, and keep the AC adapter removed from the receptacle when the equipment is not used.
•
For assistance with obtaining an exchange battery for this product in the USA, please contact:
E-mail: [email protected]
Seiko Instruments USA inc.
Thermal Printer Div.
Notes on treatment of thermal papers
•
Store the papers in a dry, cool and dark place.
•
Do not rub the papers with hard substance.
•
Keep the papers away from organic solvent.
•
Do not let the papers touched with vinyl chloride film, eraser or adhesive tapes for hours.
•
Do not put the papers on diazo print or wet copy that is just copied.
•
Use dedicated thermal papers only.
Notes on installation
•
Install the printer on a level and stable surface.
•
Avoid such places with:
Slanted surface, Strong vibration,
Direct sunlight, Full of dust, Corrosive gas,
Excessively high or low temperature
Precautions on discarding
•
When discarding used the printer, discard them according to the disposal regulations and rules of each respective
district.
２．
PREPARATION
2.1 Unpacking
Check whether a complete set is present:
•
Main body 1 unit
•
Thermal
papers
1 roll
•
Instruction
Manual
(Japanese 1, English 1, Chinese 1) 3 volumes
★
Orders for thermal papers will receive prompt attention by SII-related companies.
2.2 Components/part names
2.3
Operation panel
(1) Power
switch
Slide switch for turning power ON/OFF
(2) FEED
switch
The machine continues to feed papers when this switch is kept pressed.
(3) CHARGE
switch
Pressing this switch for 3 sec with the AC adapter connected triggers charge to the battery pack.
(4) POWER lamp (green)
This lamp lights when the power is turned ON. It flashes when the capacity of the battery pack drops low.
(5) ERROR lamp (red)
When an error occurs, this lamp lights or flashes depending on the error content.
3
．
OPERATION
3.1
Connecting AC adapter
①
Turn the power switch OFF.
②
Insert the DC plug of the AC adapter into the power
connector of the main body.
③
Insert the AC adapter into the receptacle.
[Attention!]
Do not touch the tip end of the DC plug. Before
disconnecting the AC adapter, turn the power switch OFF,
and then disconnect the AC adapter and DC plug in this
order.
3.2 Setting
papers
Opening paper cover
Press the paper cover open button, and pull the paper
cover up toward the rear of the main body with your
thumb.
Handle the paper cutter carefully not to cut
your hand.
Setting papers
①
Open the paper cover.
②
Set a paper roll as shown in the figure.
③
Close the paper cover by pressing the both end of the
cover, with the tip end of the paper emerging from the
printer.
3.3 Battery pack
Battery voltage is low with batteries that are just purchased
or long unused. Charge such batteries before use.
■
Battery charge
①
Connect
AC adapter.
②
Turn the power switch ON.
③
Keep CHARGE switch pressed for 3 sec.
When charging starts, POWER lamp and ERROR
lamp start flashing each other.
[Attention!]
Observe the following to protect secondary battery
from performance drop:
•
Charge battery in a 0 ~40
℃
temperature range.
④
When charging completes, turn off the power switch
and disconnect the AC adapter.
(The charging time is about 12 hours.)
■
If battery voltage is consumed during print,
POWER lamp flashes.
You can print out remain data by using the AC adapter.
■
Notes on use
•
When operation finishes, turn the power switch OFF.
•
The batteries discharge themselves without using.
Charge long-unused batteries once per 3 months for
a long life.
■
Removing battery pack
①
Remove the battery cover by sliding the slide switch
on rear of printer main body. (Use some thin hard one
when sliding the slide switch.)
Be careful not to hurt your hand when
handling the battery cover.
②
Take out the battery pack, and then pull out the
connector.
③
Close the battery cover.
[CAUTION]
•
Risk of explosion if battery is replaced by an incorrect
type.
•
Attend to the direction of the battery pack when you set it.
•
Dispose of used batteries according to the instructions
manual.
3.4 Maintenance
Wipe off the soiling on the printer surface with a dry soft
cloth or a cloth with a weak neutral detergent.
After that, wipe the printer with a dry cloth.
[Attention!]
•
Do not use volatile chemical as thinner or benzene.
•
Do not get printer’s inside wet with liquids such as water.
3.5 Error indication
When an error occurs, the ERROR lamp lights or flashes.
Lamps get as follows.
□
indicates that corresponding lamp lights for 0.5 sec, and
■
indicates that corresponding lamp extinguishes for 0.5 sec.
3.6 Test
In the test print mode, characters printable with the printer
are output in regular width then in double width.
Turning power switch ON with FEED switch kept pressed
triggers the test print.
3.7 Hex
dump
In hex dump mode, computer data is output in hexadecimal
numbers and characters.
Turning power switch ON with CHARGE switch kept pressed
sets the printer in hex dump print mode.
ＳＩ
Ｉ
Ｂ
Ｐ
−
Ｈ
０
０
７
Power switch
Power connector
Power
switch
Status Lamp
status
No error
(printable)
POWER
□□□□□□□□□□□□
ERROR
■■■■■■■■■■■■
Error
(No paper)
POWER
□□□□□□□□□□□□
ERROR
□□■■□□■■□□■■
Error
(Cover opened)
POWER
□□□□□□□□□□□□
ERROR
□□□□□□□□□□□□
Error
(Battery low voltage)
POWER
□□■■□□■■□□■■
ERROR
□□□□□□□□□□□□
Hardware error
POWER
□■□■□■□■□■□■
ERROR
□■□■□■□■□■□■
Charging
(Initialstatus recovers
when charging
completes.)
POWER
□■■■□■■■□■■■
ERROR
■■□■■■□■■■□■
Test print
POWER
□□□□□□□□□□□□
ERROR
□□□□□□□□□□□□
Hex dump
print
POWER
□□□□□□□□□□□□
ERROR
■■■■■■■■■■■■
ON
Function
Set mode
POWER
□□□□□□□□□□□□
ERROR
□□□□□□□□□□□□
OFF Power
OFF
POWER
■■■■■■■■■■■■
ERROR
■■■■■■■■■■■■
