SEH Dongleserver myUTN-800 Скачать руководство пользователя страница 140

Страница: 140 / 157

Appendix - Information Shown in the Display Panel (myUTN-800 only)

myUTN User Manual Windows

140

8.3

Information Shown in the Display Panel
(myUTN-800 only)

The Dongleserver myUTN-800 has a display panel at its front side. It
provides status information (error states).

Text

Description

Troubleshooting

DS
(identifier



)

The Dongleserver is operational.

The Dongleserver is restarting.

Firmware/software is loaded onto
the Dongleserver. Afterwards the
Dongleserver is updated.

One of the two power supplies is
not working.
Which connection is not working
is indicated by a glowing dot (left
dot, left power supply; right dot,
right power supply).

Check the cabling connections
and voltage source.

The SD card is formatted with an
unsupported file system
respectively cannot be read and
be written to.

Format the SD card in the file
format FAT32, FAT16 or FAT12.
Check if the SD card functions
properly.

The SD card is read-only.

Remove the write protection from
the SD card.

No SD card is available in the
card reader.

Insert an SD card into the SD
card reader:
- Type: SD or SDHC
- File system: FAT32, FAT16 or

FAT12

One or both network connections
have no link.

Check the cabling connections
and your network.

Содержание Dongleserver myUTN-800






























































































































































Результаты поиска

Содержание Dongleserver myUTN-800

Отзывы:

SEH Dongleserver myUTN-800, Руководство пользователя, Страница: 140 / 157

Результаты поиска

Содержание Dongleserver myUTN-800

Отзывы: