Code Alarm
TAMPER-PROOF
1
2
3
Made in China • Patent Pending
Test
OPERATING INSTRUCTIONS:
1. Remove screw on
resident-proof battery
compartment cover
on front of alarm.
Open battery cover
by pushing down
and out in the direction
of the arrow on battery
cover. Cover will remain
attached to alarm. Insert
three “AAA” batteries included
in package.
PLEASE NOTE:
Alarm will immediately sound
once the batteries are installed.
To shut alarm off enter pre-
programmed shut-off code
of 2-3-1. Alarm will immediately
stop sounding.
Slide battery compartment cover back in
place. Tighten tamper-proof screw. Make certain cover is
securely in place.
2. On side of alarm loosen locking security screw and slide
tamper-proof cover off alarm. To begin making your
setting decisions leave all four settings switches in the
down position.
Note: Leave switch 1 - In Room Sound
switch in the down or “ON” position while testing the
other three settings.
Press the button marked “2” on
the front of the alarm. The alarm will sound to allow you
to make your setting decisions.
Note: The alarm will
sound continuously while you are making your setting
decisions. If you wish to temporarily stop the alarm
sound at any time while making your setting decisions
simply press and hold down the “2” button. The alarm
will immediately sound again each time you release
the “2” button.
3. Use the end of a pen to move switches marked 2-Volume,
3-Tempo and 4-Tone to test each function and make your
setting decisions.
a. Switch 2 – Volume switch to desired decibel level.
The decibel range is from a high of 90 decibels with the
switch in the down position to a low of 70 decibels with
the switch in the up position.
b. Switch 3 – Tempo switch to the desired tempo from
quick in the down position to slow in the up position.
c. Switch 4 – Tone switch to the desired tone from a low
pitched alarm sound in the down position to a high
pitched alarm sound in the up position.
4. To shut the alarm off after making your setting decisions
enter the pre-programmed code of 2-3-1 by pressing the
numbered code buttons on the front of the alarm in 2-3-1
sequence. The alarm will shut off and automatically reset.
PLEASE NOTE: The pre-programmed code 2-3-1 is
embossed in the alarm casing under the battery cover
in the event the code is forgotten by a staff member.
5. If using a nurse call cable determine if you want to silence
the alarm in the resident’s room. If you want the alarm
to sound ONLY at the nurse’s station and DO NOT want
the alarm to sound in the resident’s room when using the
nurse call feature, move the switch marked 1-In Room
Sound up to the “OFF” position. If you want the alarm to
sound in BOTH the room and at the nurse’s station slide
the switch down to the “ON” position.
continued
FINALLY, A NOISELESS, RESIDENT-PROOF FALL MONITORING ALARM!
PLEASE NOTE:
THE CODE TO TURN THE ALARM SOUND OFF ON THIS ALARM HAS
BEEN PRE-PROGRAMMED AT THE FACTORY. THE CODE FOR THIS ALARM IS:
2 – 3 – 1
(This code is printed on the inside of the battery cover.)
AS A RESIDENT-PROOF SAFETY FEATURE THE ALARM SOUND ON THIS ALARM CAN ONLY BE SHUT OFF BY
PRESSING THE CODE BUTTONS ON THE FRONT OF THE ALARM IN THE NUMBER SEQUENCE ABOVE.
Personal Safety Corporation • Hiawatha, Iowa 52233 • 800.373.2873
Revised: 07/26/17
Alarm in Holder
Illustration A
Wall
Mount Screws
Included
NOTE:
For resident and pa
tient safety
& to make this alarm as tamper
-
resistant as possible you must
press and release the
TEST/RESET
button 3 times within 1.5 seconds
to stop the alarm
from sounding.
CODE ALARM w/Holder
WITH NURSE CALL INTERFACE
TAMPER-PROOF
Can Be Used with Bed Pad, Chair Pad
and Seat Belt
Model # SCA-1 • Made in China
