Sebart KatanaS 30E Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 19

background image

13

Section 7 – elevator / rudder servo & control horn installation

step 1

Locate the following , servo extension 300mm long and the servo. Install the servo hardware
(gommets and eyelets) included with the servo.

step 2

Install the elevator servo and control horn into the fuselage as per picture.

step 3

Install the rudder servo and control horn into the fuselage as per picture.

«
...
11
12
13
14
15
...
»

Содержание KatanaS 30E




















Отзывы:

Нет отзывов

Похожие инструкции для KatanaS 30E

Ultimate EP 3D Profile

Бренд: E-FLITE Страницы: 40

Бренд: Laser Pegs Страницы: 3

Бренд: Laser Pegs Страницы: 2

Бренд: AeroWorks Страницы: 17

Бренд: marklin Страницы: 20

Бренд: Radio Shack Страницы: 2

Бренд: marklin Страницы: 36

Бренд: J. Perkins Страницы: 12

Flaglor Sky Scooter

Бренд: RC GROUP Страницы: 11

Бренд: Velleman Страницы: 9

Бренд: Fisher-Price Страницы: 6

Бренд: Barbie Страницы: 2

The Harrison Dollhouse Kit

Бренд: Greenleaf Страницы: 4

6-8-6 Steam Turbine Engine

Бренд: Rail King Страницы: 32

Бренд: Bontempi Страницы: 18

Ring & Learn Cash Register

Бренд: VTech Страницы: 12

Бренд: Faller Страницы: 4

Бренд: Hobbico Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды