BeSUN Electronic Control Unit
An electronic control unit integrated into the Wind/Sun Sensor
compartment, for the automation of sun blinds and rolling
window shutters, with the possibility radio control operation for
individual and/or centralised control.
- Mod.
(BeSUN 306)
:
306
MHz
- Mod.
(BeSUN 330)
:
330
MHz
- Mod.
(BeSUN 418)
:
418
MHz
- Mod.
BeSUN 433 :
433,92 MHz
- Mod.
BeSUN 433 SET
:
“Narrow Band” 433.92
MHz
- Mod.
BeSUN 868
:
“Narrow Band” 868.3
MHz
( )
Product intended for those countries where its use is
permitted.
T
ECHNICAL
DATA
- Power supply:
230V~ 50/60Hz 2.5 W
- Motor output:
230V~ 500W Max.
- Working temperature:
-10
÷
60°C
- Radio receiver:
see model
- Compatible radio controls:
12-18 Bit or Rolling Code
- Anemometer sensitivity: 5 - 40 Km/h
- Sun sensor sensitivity: 5 - 40 Klux
- Number of codes that may be stored: 4 Max.
- Packaging dimensions: 240x185x110 mm.
- Container: PC UL94V-0 (IP54)
C
ONNECTION
OF
CN 1 T
ERMINAL
BOARD
1: Earth
2: 230V line input (Phase).
3: 230V line input (Neutral).
4: Upward movement motor output.
5: Shared motor output.
6: Downward movement motor output.
I
NITIAL
O
PERATING
CONDITION
The device can only operate in conjunction with one or more
radio controls. There is no radio control code stored in the
default factory setting.
O
PERATION
USING
DIFFERENT
M
ODELS
OF
R
EMOTE
C
ONTROL
Different models of remote control may be programmed. By
storing a code (1 button) a cyclic step by step operation (Up-
Stop-Down) may be achieved, and by storing two different
codes (2 buttons) different commands are produced, one for
Up and one for Down. Storing three different codes (3 “BeFree”
series buttons) produces three different commands: the first for
Up, the second for Stop and the third for Down.
Operation using a 1-button radio control:
The following type of operation is obtained using a radio-
control with a single button: The first press controls the upward
movement until the motor stops (the motor has a running time
of around 2 minutes). The second press controls the downward
movement of the shutter. If the button is pressed before the
motor stops running, the control unit will stop the shutter
moving and the button will need to be pressed again to
reactivate the motor in the opposite direction.
Operation using a 2-button radio control:
By using a radio control with 2 buttons, the following processes
may be carried out: the first button, “Up”, controls the upward
movement for about 2 minutes, until the motor has stopped
running and the second button (“Down”) controls the downward
movement of the shutter. If the upward movement is
interrupted with another “Up” command, the motor will continue
to run in the upward movement direction. If, however, the
movement is interrupted with a “Down” command, the control
unit will stop the motor.
The procedure is the same for the down movement phase.
Operation using a 3-button radio control (BeFree x1):
The following type of operation is obtained using the
BeFree
x1
radio control: the (Up) key controls the upward movement
until the end of the motor time (2 minutes), the (Stop) key
makes the shutter stop and the (Down) key controls the
downward movement. If a stop command is sent during the
upward or downward movement, the control unit causes the
shutter to stop. If a command that is in the opposite direction to
the current movement is sent during the upward or downward
movement, the control unit causes the shutter to change
direction.
Operation using a 3-button radio control (BeFree x3):
When using the
BeFree x3
radio control, you will obtain the
same operation as previously described for the BeFree x1
version; in addition, by using the keys (-) and (+) at the sides of
the radio control it is possible to enable and disable the sun
sensor (the selection is confirmed by a quick Up / Down
movement of the motor).
Operation using a 3-button radio control (BeFree x6):
When using the
BeFree x6
radio control, you will obtain the
same operation as previously described for the BeFree x1
version; in addition, by using the keys (-) and (+) at the sides of
the radio control it is possible to select the UP – STOP –
DOWN controls for 6 different types of use.
I
NVERSION
OF
THE
ROTATION
MOTOR
If you notice that when pressing the UP key on the radio-
control the control unit causes the shutter to move upwards
instead of downwards, all you have to do is simply repeat the
programming procedure pressing the DOWN key instead of the
UP key, or invert the motor’s Upward movement wire with the
Downward movement wire.
G
ROUP
OR
G
ENERAL
C
ENTRALISATION
It is also possible to insert two identical codes (buttons) from
one radio control to all the control units or a group of them that
are situated at a maximum distance of 20 metres from the point
of command, in order to obtain general or partial motion of
more than one automation.
A
NEMOMETER
O
PERATION
The electronic control unit will control the upward movement of
the sun shade every time the wind exceeds the selected
threshold.
S
UN
S
ENSOR
O
PERATION
The electronic control unit controls the downward movement of
the sun shade after 5 minutes during which the brightness is
greater than the threshold selected using the VR1 trimmer and
displayed by means of the SUN LED; it also controls the
upward movement of the shade after 5 minutes during which
the brightness is below the selected threshold.
When the SUN LED lights up on the control unit, this indicates
that the sun’s intensity exceeds the threshold selected using
the VR1 trimmer; this enables you to use the current light
conditions as a reference when setting the desired value.
O
PERATION
PRINCIPLES
SW1 SW1 SW1 SW1
Step-by-step P/P + Down mov. Sun Sensor Test Anemometer
Test
Step-by-step (Dip 1 and 2 OFF)
The following type of operation may be obtained using the
BeFree xx radio control: the Up key controls the upward
movement until the end of the set motor time (2 minutes), the
Stop key makes the shutter stop and the Down key controls
the downward movement. If a stop command is sent during the
1
Rev. 1.4 20-05-2009
GB
Содержание BeSUN
Страница 4: ...4 Rev 1 4 20 05 2009 ...
