Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
WL183D Issue: 2 (H F I) - 26/02/18
Original Language Version
© Jack Sealey Limited
Refer to instruction
manual
FREESTANDING FLEXIBLE WORK LIGHT
18 SMD LED
MODEL NO:
WL183D
1. SAFETY
1.1. Electrical Safety
WARNING!
It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
Important
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
8
DO NOT
pull or carry the appliance by the power cable.
8
DO NOT
pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT
use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
qualified electricia
n.
1.1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal ‘L’.
B) Connect the BLUE neutral wire to the neutral terminal ‘N’.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO NOT
connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualified electrician.
2. INTRODUCTION
Powerful 3 diopter 89mm precision lens gives high quality magnifying capabilities. Features 18 SMD LEDs to illuminate the object for improved
detailed work. Flexible work arm allows simple positioning of the lamp to suit task. Ideal for electrical engineers, engravers and fine detail work.
Supplied with BS approved plug.
3. SPECIFICATION
Model No:
.............................................
WL183D
LEDs: .....................................................18 SMD
Supply:...................................................230V
4. OPERATION
4.1.
Turn on and off using the switch on top.
4.2.
Manoeuvre the work lamp into the ideal position to
suit task.
Note:
Be aware of the effect of using the lamp close to a
window/door where it could be in direct sunlight.
Remember to close the lid on top whilst it is not in
use.
Recommended fuse
rating:3A
