instructions for
wheel balancer - Semi automatic
model no:
wb10
thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. Safety
1.1.
electrical Safety
warninG!
it is the user’s responsibility to check the following:
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and
all electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey dealer.
if used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable Appliance test) tested.
electrical safety information, it is important that the following information is read and understood.
9
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9
regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
9
Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct fuse - see
fuse rating in these instructions.
8
Do not
pull or carry the appliance by the power cable.
8
Do not
pull the plug from the socket by the cable.
8
Do not
use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or replaced immediately by a
qualified electrician.
9
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
if the cable or plug is damaged during use, switch off the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
General Safety
9
Make sure Wheel Balancer is fitted/used on a dry, flat, level, oil/grease free, concrete surface capable
of
supporting the weight of the Wheel Balancer.
9
Before each use, always examine the wheel balancer for structural cracks/defects, damage to
the safety guard and electrical wiring, and any other condition that may affect the safe operation
of the machine.
Do not
use the Wheel Balancer if any defects are found.
9
maintain a safe working environment. Keep the work area well lit. make sure there is adequate surrounding workspace. Always keep
the work area free of obstructions, grease, oil and other debris.
8
Do not
use the Wheel Balancer in a damp or wet location.
Do not
use the Wheel Balancer in areas near flammable chemicals, dusts or vapours.
9
this wheel balancer is designed for use with most passenger cars and light commercial wheels.
Do not
attempt to exceed the
machine’s maximum wheel diameter of 28”.
8
Do not
raise the safety guard until the spinning wheel comes to a complete stop.
9
Always keep hands, fingers, and feet away from the moving parts of the wheel balancer while machine is in use.
8
Do not
leave the wheel balancer unattended when it is running. After completing a wheel balancing function, always turn the Power
switch to its “off” position, and wait until the machine comes to a complete stop before leaving.
9
Before turning the machine on, make sure tools, tool trays, wheel weights, and all other
equipment is removed immediately from the
vicinity.
8
Do not
stand or allow an observer to stand in line with the spinning wheel.
8
Do not
use with an extension cable. Wheel Balancer needs to be mounted near a suitable plug socket.
9
Always unplug the wheel balancer from its electrical supply before performing any inspection, maintenance, or cleaning procedures.
warninG:
People with pacemakers should consult their physician(s) before using this product.
operation of electrical equipment in
close proximity to a heart pacemaker could cause interference or failure of the pacemaker.
recommended fuse rating
13 Amp
WB10 | Issue 1 05/02/18
Original Language Version
© Jack sealey limited
refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear safety
footwear
Wear protective
clothing
Keep in dry area
protect from rain
Wear a mask
