background image

instructions for

STARTER/CHARGER 300AMP,400AMP,500AMP 

12/24V

model no: 

SUPERSTART300.V5/SUPERSTART

              400.V2/SUPERSTART500.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these 

instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  SAFETY

  

Electrical Safety

 

‰

  

WARNING!

 it is the user’s responsibility to check the following:

 

check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and    

 

all electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical  

 

products. You may obtain an rcd by contacting your local sealey dealer. 

 

if the charger is used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable Appliance  

 

test) tested.

 

electrical safety information, it is important that the following information is read and understood.

1.0.1.   

ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. 

1.0.2.   

regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure  

 

that they are secure.

Important

: ensure that the voltage rating on the appliance suits the power supply to be  

 

used and the correct type of plug fitted.

 

8

   DO  NOT

 pull or carry the appliance by the power cable.

 

8

  

DO NOT

 pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm  

  grip on the plug.

 

8

   DO  NOT

 use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or  

  replaced immediately by a qualified electrician.

1.0.3.   

if the cable or plug is damaged during use, switch the off electricity supply and remove from use. 

1.0.4.   

this product requires an electrical supply in excess of 13 amps, and no plug is fitted. 

 

You must therefore contact a qualified electrician to ensure that a 16 amp supply is available.

 

We recommend that you discuss the installation of a industrial round pin plug and socket with your electrician. 

 

ensure that the unit is correctly earthed via a three-pin plug, as shown. 

 

a)  connect the green/yellow earth wire to the earth terminal 

 

b)  connect the brown live wire to live terminal ‘l’.

 

c)  connect the blue neutral wire to the neutral terminal, ‘n’ or unmarked.

 

d)  After wiring, check that there are no bare wires, that all wires have been correctly connected,

 

     that the external insulation extends beyond the cable restraint and that the restraint is tight.

 

 

Sealey recommend that repairs are carried out by a qualified electrician.

 

“Modern vehicles contain extensive electronic systems.You are required to check with the vehicle Manufacturer, for any specific

 

instructions regarding the use of this type of equipment on each vehicle.”

 

“no liability will be accepted for damage / injury, where this product is not used in accordance with all instructions.”

  

 

   DANGER! BE AWARE, LEAD-ACID BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION.   

  FOR THIS REASON, IT VERY IMPORTANT TO READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY, EACH TIME YOU USE  

  THE CHARGING EQUIPMENT. 

1.0.5. 

  

follow these instructions and those published by the battery and vehicle manufacturers, and the maker of any equipment you intend to  

 

use in the vicinity of the battery. remember to review warning marks on all products and on engines.

 

‰

  

WARNING!

 modern vehicles contain extensive electronic systems.

 

You are required to check with the vehicle Manufacturer, for any specific instructions regarding the use of this type of equipment on    

 

each vehicle.

1.0.6.   

no liability will be accepted for damage / injury, where this product is not used in accordance with all instructions.

1.1.    

Personal Precautions

 

9

 

ensure there is another person within hearing range of your voice and close enough to come to your aid, 

   

should a problem arise when working near a lead-acid battery.

 

9

   Wear safety eye protection and protective clothing. Avoid touching eyes while working near battery.

 

9

   Have fresh water and soap nearby in case battery acid contacts skin, clothing or eyes.

Original Language Version

© Jack sealey limited

Wear 

Protective 

Gloves

Warning:

electricity

Protect 

from 

rain

use in

Well 

ventilated

Areas 

Keep away 

from sources 

of ignition:

battery could 

explode

refer to

instruction 

manual

Warning:

explosive

material

Wear eye

Protection

Warning:

corrosive 

substance

it is recommended

that the supply to this 

product is fitted with a 

16AmP fuse or breaker

suPerstArt300.v5,400.v2,500. | issue (1) 05/07/16

Содержание SUPERSTART300.V5

Страница 1: ... you discuss the installation of a industrial round pin plug and socket with your electrician Ensure that the unit is correctly earthed via a three pin plug as shown a Connect the green yellow earth wire to the earth terminal b Connect the brown live wire to live terminal L c Connect the blue neutral wire to the neutral terminal N or unmarked d After wiring check that there are no bare wires that ...

Страница 2: ...unauthorised persons away from the working area 8 8 DO NOT dis assemble the charger for any reason The charger must only be checked by qualified service personnel 8 8 DO NOT try to charge a non rechargeable battery 8 8 DO NOT try to charge battery if battery fluid is frozen WARNING To prevent the risk of sparking short circuit and possible explosion DO NOT drop metal tools in the battery area or a...

Страница 3: ...carrying out the following steps and in the same order 4 3 1 Before charging make sure the power supply lead is not plugged into the mains supply 4 3 2 Set the charger voltage 12V or 24V according to the nominal voltage of the battery being charged by moving the red cable to the appropiate terminal Note To charge several batteries at the same time see the series parallel diagram in fig 2 4 3 3 Con...

Страница 4: ...stances 5 1 1 Overload too high a current to the battery 5 1 2 Short circuit clamps touch or cross connection to battery 5 1 3 Prolonged starting attempts 5 2 Should the fuse blow take the following action 5 2 1 Turn the unit off and disconnect from the mains power supply 5 2 2 Allow the unit to cool down establish the reason for failure and correct 5 2 3 Replace the fuse Use only Sealey replaceme...

Отзывы: