InstructIons for:
starter/charger
model no:
sUPerstart1020.V3
IMPORTANT:
PLease reaD these INstrUctIONs careFULLY. NOte the saFe OPeratIONaL reQUIreMeNts, WarNINgs aND caUtIONs. Use thIs
PrODUct cOrrectLY aND WIth care FOr the PUrPOse FOr WhIch It Is INteNDeD. FaILUre tO DO sO MaY caUse DaMageaND/Or PersONaL
INJUrY aND WILL INVaLIDate the WarraNtY. PLease retaIN these INstrUctIONs FOr FUtUre Use.
thank you for purchasing a sealey product. manufactured to a high standard this product will give you years of trouble free performance if these instructions are
carefully followed and the product is correctly maintained.
1. saFetY INstrUctIONs
IMPOrtaNt: the sUPerstart1020.V2 MUst Be cONNecteD tO a 3 Phase 415 VOLt sUPPLY. (see sectION 1.2)
the FOLLOWINg stateMeNts ON eLectrIcaL saFetY MUst aLsO Be reaD aND UNDerstOOD BeFOre UsINg the
starter/charger.
1.1.
eLectrIcaL saFetY.
WarNINg! It is the user’s responsibility to check the following:
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads,
plugs and all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of
appropriate safety devices. An rccB (residual current circuit Breaker) should be incorporated in the main distribution board.
We recommend that an rcd (residual current device) is used with all electrical products. It is particularly important to use an rcd
with portable products that are plugged into an electrical supply not protected by an rccB. If in doubt consult a qualified electrician.
You may obtain a residual current device by contacting your sealey dealer. You must also read and understand the following
instructions concerning electrical safety.
1.1.1. the electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
person, using a Portable Appliance tester (PAt), at least once a year.
1.1.2. the Health & safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and
the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3.
DO
ensure the insulation on all cables and the product itself is safe before connecting to the mains power supply. see 1.2.1. above
and use a Portable Appliance tester (PAt).
1.1.4.
DO
ensure that cables are always protected against short circuit and overload.
1.1.5.
DO
regularly inspect power supply, leads, plugs for wear and damage and all electrical connections to ensure that none is loose.
1.1.6.
DO
check that the voltage marked on the product is the same as the electrical power supply to be used and check that all fused plugs
are fitted with the correct capacity fuse.
1.1.7.
DO NOt
pull or carry the powered appliance by its power supply lead and do not pull plug by the cable. Products must not be pulled or
carried by their output cables.
1.1.8.
DO NOt
use worn or damage leads, plugs or connections. Immediately replace or repair by qualified persons.
1.1.9.
We do not recommend tHe use of An extensIon cABle WItH tHe cHArger As tHe PoWer outPut mAY Be serIouslY reduced.
1.2
WarNINg!
ElEcTRIcAl INsTAllATION Of THE sUPERsTART1020 TO A 3 PHAsE 415VOlT sUPPly
MUsT ONly bE cARRIEd OUT by A qUAlIfIEd ElEcTRIcIAN.
Make sure the power supply cable is correctly
connected to the Earth. It is the user’s responsibility to read, understand and comply with the following:
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads,
plugs and all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation
of appropriate safety devices. An rccB (residual current circuit Breaker) should be incorporated in the main distribution board.
1.3. PersONaL PrecaUtIONs
ensure there is another person within hearing range of your voice, or close enough
to come to your aid, should a problem arise when working near a lead-acid battery.
Wear safety eye protection and protective clothing. Avoid touching eyes while working near battery.
Have fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes.
Wash immediately with soap and water if battery acid contacts skin or clothing. If acid enters eye, flush eye immediately with cool, clean
running water for at least 15 minutes and seek immediate medical attention.
remove personal metallic items such as rings, bracelets, necklaces and watches. A lead-acid battery can produce a short-circuit current
high enough to weld a ring or the like to metal, which may cause severe burns.
ensure hands, clothing (especially belts) are clear of fan blades and other moving or hot parts of engine, remove ties and contain long hair.
do not smoke or allow a spark or flame in the vicinity of battery or engine.
DaNger! Be aWare, LeaD-acID BatterIes geNerate eXPLOsIVe gases DUrINg NOrMaL BatterY OPeratION. FOr thIs reasON,
It Is VerY IMPOrtaNt tO reaD aND FOLLOW these INstrUctIONs careFULLY, each tIMe YOU Use the chargINg eQUIPMeNt.
Follow these instructions and those published by the battery and vehicle manufacturers and the manufacturer of any equipment
you intend to use in the vicinity of the battery. Remember to review warning marks on all products and on engines.
Original Language Version
suPerstArt1020.V3 Issue: 3 - 22/10/10
1.2.1 This product must be fitted with a 3 phase plug according to the diagram to the right, and
will require a minimum of 16AMPs per phase, (preferably 32AMP) electrical supply. you
must contact a qualified Electrician to ensure an appropriately fused supply is available.
connect greeN/YeLLOW wire to earth ‘e’
connect greY wire to L1 terminal.
connect BrOWN wire to L2 terminal.
connect the BLacK wire to terminal L3.
When completed, check there are no bare wires, that all wires have been connected
correctly and the cable restraint is tight.
1.2.2 DO NOt use this product with a standard extension cable. Only use arMOUreD extension
cable.
