background image

InstructIons For: 

TOWER FAN

MoDEL no: 

STF29T 

thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and 
properly maintained, give you years of trouble free performance.

1.  SAFETY  INSTRUCTIONS

IMPORTANT:  PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND 
CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY 
CAUSE DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

1.2        GENERAL SAFETY

  Disconnect the fan from the mains power when not in use, and before servicing or performing any maintenance.

 use the fan in dry areas only. Do not use in wet or high condensation locations such as bathrooms, showers, or pools. 

  WARNING! 

If a fan falls into water, immediately switch off at the mains and disconnect from the mains power supply.      

 

Do not touch the fan until the mains power supply has been disconnected.

  Always disconnect the fan from the power supply when moving it from one location to another.

  Keep the fan clean and maintain in good condition (use an authorised service agent).

 use recommended parts only (non genuine parts may be dangerous, and will invalidate your warranty).

 

Do not stand the fan where it may be knocked over or off a surface, or where the lead may cause a person 

 

to trip.

 

Do not use an extension cord unless it has been approved by an electrical authority. 

 

Do not insert any objects through the fan guard. 

 

Do not allow children to operate the fan. 

 

Do not immerse the fan in water or any other liquid. 

 

Do not use the fan outdoors.

 

 When not in use store in a safe, dry, childproof location. 

 

Do not cover the fan.

2.1. 

Your tower Fan is supplied fully assembled with the exception of the base which comes in two halves.   

 

Please follow the assembly instructions carefully.

2.2 

Assembling the base. 

 click the two halves of the base together, around the mains lead, and screw to  

 

the bottom of the fan Assembly as shown in fig.1. Fit the cable clamp over the mains lead, using the two  

 

screws provided and secure the mains lead into the lead retainer as shown in fig.2.  the unit is 

now fully  

 

assembled and ready for use.

2.   ASSEMBLY 

1.1. 

ELECTRICAL SAFETY

  

WARNING!

 It is the responsibility of the owner and the operator to read, understand and comply with the following:

You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other 
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. 
A residual current circuit Breaker (rccB) should be incorporated in the main distribution board. We also recommend that a residual current 
Device (rcD) is used. It is particularly important to use an rcD with portable products that are plugged into a supply which is not protected 
by an rccB. If in any doubt consult a qualified electrician. You may obtain a residual current Device by contacting your sealey dealer. 

You must

 also read and understand the following instructions concerning electrical safety.

1.1.1. the 

Electricity at Work Act 1989 

requires all portable electrical appliances, if used on business premises, to be tested by a qualified  

 

electrician, using a Portable Appliance tester (PAt), at least once a year.

1.1.2.  the 

Health & Safety at Work Act 1974 

makes owners of electrical appliances responsible for the safe condition of those appliances  

 

and the safety of the appliance operators. 

If in any doubt about electrical safety, contact a qualified electrician.

1.1.3.  Ensure that the insulation on all cables and on the appliance is safe before connecting it  
 

to the power supply. see 1.1.1. and 1.1.2. and use a Portable Appliance tester.

1.1.4.  Ensure that cables are always protected against short circuit and overload.
1.1.5.  regularly inspect power supply cables and plugs for wear or damage and check all
 

connections to ensure that none is loose.

1.1.6. 

Important:

 Ensure that the voltage marked on the appliance matches the power supply 

 

to be used and that the plug is fitted with the correct fuse - see fuse rating at right.

1.1.7. 

DO NOT

 pull or carry the appliance by the power cable.

1.1.8. 

DO NOT 

pull the plug from the socket by the cable.

1.1.9. 

DO NOT

 use worn or damaged cables, plugs or connectors. Immediately have any faulty 

 

item repaired or replaced by a qualified electrician. When an AstA/Bs approved uK 

 

3 pin plug is damaged, cut the cable just above the plug and 

dispose of the plug safely. 

 

Fit a new plug according to the following instructions (uK only).

 

a)  Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.

 

b)  Connect the BROWN live wire to the live terminal ‘L’.

 

c)  Connect the BLUE neutral wire to the neutral terminal ‘N’.

 

d)  After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulation  

 

extends beyond the cable restraint and that the restraint is tight.

 

Double insulated products, which are always marked with this symbol      , are fitted with live (brown) and neutral (blue) wires only.  

 to rewire, connect the wires as indicated above - 

DO NOT

 connect either wire to the earth terminal.

1.1.10.  Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure that  
 

a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket with your   

 

electrician.

1.1.11.  If an extension reel is used it should be fully unwound before connection. A reel with an rcD fitted is preferred since any appliance  
 

plugged into it will be protected. the cable core section is important and should be at least 1.5mm², but to be absolutely sure that   

 

the capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the   

 

use of 2.5mm² section cable.  If extension reel is to be used outdoors, ensure it is marked for outdoor use.

FUSE RATING 5 AMP

Blue 
Neutral 
Wire

Yellow & Green 
Earth Wire 

Cable 
Restraint

Brown
Live 
Wire

Fig.2.

Fig.1.

Original Language Version

stF29t    Issue: 3 - 14/04/10

Отзывы: