SOLAR PANELS
MODEL NO’S:
SPP01.V2 (12V/1.5W), SPP02.V1 (12V/2.4W),
SPP03.V2 12V/4.8W
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9
Observe standard safety procedures when using these items.
▲
DANGER
! - Beware, lead-acid batteries generate explosive
gases during normal battery operation.
9
If the battery terminals are corroded or dirty, clean them before
attaching the clips.
9
Remove ill fitting clothing. Remove ties, watches, rings and
other loose jewellery. Contain, or tie back, long hair when
working near batteries.
9
Keep children and unauthorised persons away from connections.
WARNING!:
DO NOT
use solar panels on any vehicles other than
those with12Volt DC systems.
8
DO NOT
dis-assemble solar panel. The solar panel must be
checked by qualified service personnel only.
8
DO NOT
get solar panel wet or use in damp locations or areas
where there is condensation.
8
DO NOT
use the solar panel for any purpose other than for which
it is designed.
8
DO NOT
pull the cables or clips from the battery terminals.
8
DO NOT
operate the solar panel if damaged.
9
When not in use store in a safe, dry, childproof location.
2. INTRODUCTION
Amorphous solar panels convert daylight directly into 12V electricity. Suitable for maintaining charge in a wide range of batteries and power
packs. Ideal for batteries stored in boats and caravans and for batteries in vehicles in long-term storage. IP44 Rating (non-waterproof). For
use behind car windscreen or other protection. Supplied with battery clips and vehicle accessory socket plug (only suitable for vehicles with
“permanent live” accessory socket).
3. SPECIFICATION
Model no: ..............................................................SPP01.V2
Output: ................................................................... 12V/1.5W
Dimensions: ......................................................350 x 125mm
IP Rating .........................................................................IP44
Model No. ..............................................................SPP02.V1
Output .................................................................... 12V/2.4W
Dimensions: ......................................................375 x 215mm
IP Rating: ........................................................................IP44
Model no: ..............................................................SPP03.V2
Output: ................................................................... 12V/4.8W
Dimensions: ......................................................440 x 345mm
IP Rating .........................................................................IP44
4. OPERATION
4.1.
INSTALLATION
4.1.1.
Insert the suction cups (SPP01.V2, SPP02.V1 only) into the pre-drilled ends of the solar panel ensuring that they are securely fixed.
Choose a clean, dry surface, facing the sun, then dampen suction cups and mount to vehicle’s dash or windscreen.
4.2.
CONNECTION THROUGH VEHICLE ACCESSORY SOCKET (Only suitable for vehicles with “permanent live” accessory
socket)
4.2.1.
Attach the auxiliary adaptor lead to the solar panel lead. Plug the male-end of the auxiliary adaptor (12V plug) into the female auxiliary
socket (in the vehicle) making sure that both ends are secure and aligned correctly. For optimal charging power, ensure the panel
(solar cell up) is directly facing the sun. For vehicles that do not have permanent live accessory sockets refer to:
SPP01.V2, SPP02.V1, SPP03.V2 Issue:3 (3,4) 11/06/20
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Connect to any 12V auxiliary
power outlet
Connect directly to battery
using DC cables
Connect to any 12V auxiliary
power outlet
Connect directly to battery
using DC cables
