instructions for
oscillating multi-tool 180W/230V
model no:
smt180.V2
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. saFEtY
1.1.
ElEctRical saFEtY
WaRning!
it is the user’s responsibility to check the following:
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and all
electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey dealer.
if the tool is used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable Appliance
test) tested.
electrical safety information, it is important that the following information is read and understood.
1.1.1.
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
important
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct
fuse - see fuse rating in these instructions.
8
Do not
pull or carry the appliance by the power cable.
8
Do not
pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
Do not
use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or replaced immediately by a
qualified electrician.
1.1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
if the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
class ii products are wired with live (brown) and neutral (blue) only are marked with the class ii symbol;
A) Connect the BROWN live wire to the live terminal ‘L’.
B) Connect the BLUE neutral wire to the neutral terminal ‘N’.
c) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
8
Do not
connect either wire to the earth terminal.
9
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
gEnERal saFEtY
9
only power the tool from the mains supply.
9
disconnect the tool from the mains supply before changing accessories, servicing or performing any
9
maintenance.
9
maintain tool and accessories in good condition. check moving parts and alignment. if necessary use an authorised service agent.
9
replace or repair damaged parts using recommended parts. unauthorised parts may be dangerous and will invalidate the warranty.
9
Wear approved safety goggles and a dust mask if generating dust.
9
remove ill fitting clothing. remove ties, watches, rings and other loose jewellery and contain long hair.
9
use the tool in a suitable work area. Keep area clean and tidy and free from unrelated materials and ensure that there is adequate lighting.
9
Prevent body contact with earthed surfaces to avoid electric shock e.g. pipes, radiators, refrigerators etc.
9
maintain correct balance and footing.
9
Keep children and unauthorised persons away from the work area.
9
secure unstable workpiece with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Keep the tool clean for best and safest performance.
9
When not in use switch tool off and unplug it from the mains supply. Store it in the case and put in a dry, childproof area.
8
Do not
over-reach. ensure the floor is not slippery and wear non-slip shoes.
8
Do not
use the tool for a task it is not designed to perform.
8
Do not
operate tool where there are flammable liquids or gases.
8
Do not
get the tool wet or use in damp or wet locations.
8
Do not
carry the tool by the cable.
8
Do not
hold unsecured work in your hand.
8
Do not
leave the tool running unattended.
8
8
88
Do not
operate the tool if any parts are missing or damaged as this may cause failure and/or personal injury.
8
8
88
Do not
operate the tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.
s
MT180.V2| Issue:1 12/05/17
Original Language Version
© Jack sealey limited
refer to
instruction
manual
Wear ear
protection
Wear eye
protection
Wear
respiratory
protection
recommended fuse rating
3 Amp
