parts cleaning tank/portable
model no:
sM21.V4
thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. safety
1.1.
electrical safety
Warning!
It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets
and any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of
appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. You
must also read and understand the following instructions concerning electrical safety.
9
ensure that cables are always protected against short circuit and overload.
9
Regularly inspect power supply cables and plugs for wear or damage and check all connections
to ensure that none are loose.
9
ensure that the voltage marked on the appliance matches the power supply to be used and that
the plug is fitted with the correct fuse - see fuse rating at right.
8
Do not
use worn or damaged cables, plugs or connectors. Have any faulty item repaired or
replaced immediately by a competent electrician.
9
It is recommended that this heater is wired directly to a fused isolator switch. If, however, a plug
is fitted, the following applies:
9
Fit a new plug according to the following instructions (UK only).
a) Connect the GReen/YelloW earth wire to the earth terminal ‘e’.
b) Connect the BRoWn live wire to the live terminal ‘l’.
c) Connect the BlUe neutral wire to the neutral terminal ‘n’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected,
that the cable restraint is tight.
1.2.
general safety
Warning!
ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
equipment.
9
Familiarise yourself with product application and limitations, as well as the specific potential hazards peculiar to the cleaning tank.
Warning!
disconnect the cleaning tank from the mains power before changing accessories, servicing or performing any maintenance.
9
maintain the cleaning tank in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
Warning! Do not
modify the lid or prop it open. Keep the lid and holding screws in place, tight and in good working order.
9
locate the cleaning tank in an adequate working area for its function. ensure the cleaning tank is stood on a firm level surface. Keep
area clean and tidy and free from unrelated materials. ensure the area is well ventilated and has adequate lighting.
9
Keep the cleaning tank away from heat sources such as heater, sparks, open flames etc.
9
Keep the tank clean. Remove and clean the filter regularly for best and safest performance.
9
ensure there are no flammable or combustible materials near the work area.
Warning!
Always wear approved eye or face protection when operating the cleaning tank.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain long hair.
9
Wear appropriate protective clothing.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the working area.
9
Avoid accidental starting of the cleaning tank. ensure that it is unplugged from the mains supply when not in use.
9
Incase of fire in parts unit, close the lid, do not attempt to remove parts, or the cleaning tank.
8
Do not
use the cleaning tank for any purpose other than for which it is designed.
8
Do not
use cleaning tank in wet or damp locations or areas where there is condensation.
8
Do not
use the cleaning tank where there are flammable liquids, solids or gases.
8
Do not
allow untrained persons to operate the cleaning tank.
8
Do not
over fill the cleaning tank with solvent. Full capacity should be just below the parts tray.
8
Do not
operate the cleaning tank if any parts are missing or damaged as this may cause failure or possible personal injury.
8
Do not
modify or jam the cleaning tank lid open. Retain the lid open by use of the attached elbow strut only.
8
Do not
use any solvent with a flash point below 105°F. Use only Sealey solvent, contact your local Sealey stockist for details.
Sm21.V4 | Issue 2 26/03/18
Original Language Version
© Jack Sealey limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
recommended fuse rating
3 amp
