InstructIons for:
jigsaw VaRiaBLE sPEED 750w
MoDEL no:
sjs700.V2
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT
:
PLEasE REaD THEsE iNsTRUCTiONs CaREFULLY. NOTE THE saFE OPERaTiONaL REQUiREMENTs, waRNiNgs aND CaUTiONs.
UsE THis PRODUCT CORRECTLY aND wiTH CaRE FOR THE PURPOsE FOR wHiCH iT is iNTENDED. FaiLURE TO DO sO MaY CaUsE DaMagE
aND/OR PERsONaL iNjURY aND wiLL iNVaLiDaTE THE waRRaNTY. RETaiN THEsE iNsTRUCTiONs FOR FUTURE UsE.
1.1
ELECTRiCaL saFETY
waRNiNg!
It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other con-
nectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A
residual current circuit Breaker (rccB) should be incorporated in the main distribution board. We also recommend that a residual current
Device (rcD) is used. It is particularly important to use an rcD with portable products that are plugged into a supply which is not protected by an
rccB. If in any doubt consult a qualified electrician. You may obtain a residual current Device by contacting your sealey dealer.
You must
also read and understand the following instructions concerning electrical safety.
1.1.1 the
Electricity at work act 1989
requires that all portable electrical appliances, if used on business premises, are tested by a qualified
electrician, using a Portable Appliance tester (PAt), at least once a year.
1.1.2 the
Health & safety at work act 1974
makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators.
if in any doubt about electrical safety, contact a qualified electrician.
1.1.3 Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. see 1.1.1. and 1.1.2. and
use a Portable Appliance tester.
1.1.4 Ensure that cables are always protected against short circuit and overload.
1.1.5 regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none are loose.
1.1.6
important:
Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7
DO NOT
pull or carry the appliance by the power cable.
1.1.8
DO NOT
pull the plug from the socket by the cable.
1.1.9
DO NOT
use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When a Bs 1363/A uK 3 pin plug is
damaged, cut the cable just above the plug and
dispose of the plug safely.
fit a new plug according to the following instructions (uK only).
a) Connect the gREEN/YELLOw earth wire to the earth terminal ‘E’.
b) Connect the BROwN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) after wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulation
extends beyond the cable restraint and that the restraint is tight.
Double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only.
to rewire, connect the wires as indicated above -
DO NOT
connect either wire to the earth terminal.
1.1.10 Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure that
a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket with your
electrician.
1.1.11 If an extension reel is used it should be fully unwound before connection. A reel with an rcD fitted is preferred since any appliance
plugged into it will be protected. the cable core section is important and should be at least 1.5mm
2
, but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use of
2.5mm
2
section cable.
1. saFETY iNsTRUCTiONs
FUsE RaTiNg
5 aMP
Blue
Neutral
Wire
Yellow & Green
Earth Wire
Cable
Restraint
Brown
Live
Wire
1.2
gENERaL saFETY
Disconnect the jig saw from the mains power before changing accessories, servicing or performing any maintenance.
Keep saw in good condition. check moving parts and alignment, and keep saw blades sharp. If necessary use an authorised service agent.
replace or repair damaged parts.
Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Keep the jig saw clean for best and safest performance.
Wear approved safety eye protection with side shields, and a dust mask if jig saw generates dust.
remove ill fitting clothing. remove ties, watches, rings, other loose jewellry and contain long hair.
use the jig saw in a suitable working area, keep area clean and tidy and free from unrelated materials, and ensure there is adequate lighting.
use the correct type of blade for the task, such as cutting wood, resin board, ceramic tiles, plastics, copper tubing and thin metal sheeting.
Prevent body contact with grounded surfaces to avoid electric shock i.e. pipes, radiators, ranges, refrigerators etc.
Evaluate your working area before using the jig saw i.e. floors and enclosures may contain hidden electrical wires or water piping.
Maintain correct balance and footing.
DO NOT
over-reach and ensure the floor is not slippery and wear non skid shoes.
Keep children and unauthorised persons away from the working area.
secure non stable work piece with a clamp, vice or other adequate holding device.
Avoid unintentional starting, and ensure the lock on button is disengaged before use.
Ensure the power cable is kept to the rear of the saw.
DO NOT
force jig saw but allow the saw to progress normally. force may break the blade.
DO NOT
secure the saw in a clamp or vice.
DO NOT
use the saw without it’s front guard down and before you have checked blade is secured.
DO NOT
touch the blade and
DO NOT
point the blade at yourself and/or others.
DO NOT
operate jig saw where there are flammable liquids or gasses.
DO NOT
get the jig saw wet or use in damp or wet locations.
DO NOT
hold unsecured work in your hand.
DO NOT
turn the saw on whilst the blade is in a workpiece.
s
DaNgER! DO NOT
shine laser beam into your or anybody elses eyes.
Original Language Version
sJs700.V2 Issue: 2 - 23/11/09
