BOTTLE JACKS
MODEL NO:
SJ2.V3, SJ3.V3, SJ5.V3, SJ8.V3, SJ10.V3,
SJ12.V3, SJ15.V3, SJ20.V3, SJ30.V4
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9
Inspect and lubricate the jack regularly to ensure it is in good working order and condition.
DO NOT
use the jack if damaged or a fault is
suspected - check Section 6 Troubleshooting. If necessary, immediately repair or replace damaged parts.
9
Use recommended parts only, the use of unauthorised parts may be dangerous and will invalidate your warranty.
9
Ensure the work area is clean, tidy and free from unrelated materials and has adequate lighting.
9
Use jack on level and solid ground, preferably concrete. Avoid tarmacadam since jack may sink in.
9
Park the vehicle and apply hand brake (if automatic, place in “Park” mode). Switch off the engine and place chocks under the wheels.
9
Ensure a minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc. to allow for tilting during jacking.
9
Ensure all persons are out of the vehicle before jacking.
DO NOT
enter vehicle whilst it is supported on the jack or axle stands.
9
Check vehicle weight and recommended lifting points by referring to the vehicle owner’s manual. Ensure the lifting point is not corroded.
9
Check lifting point is centred and stable on jack saddle (off centre loads can slip). Position jack so as to avoid operating it from under
vehicle.
9
Keep all unauthorised persons away from the jack when lifting and lowering.
▲
DANGER
! Use the jack for lifting only, NOT for supporting the lifted load. ALWAYS USE ADEQUATELY RATED AXLE STANDS.
9
Keep hands etc. clear of moving parts during raising and lowering of the vehicle.
▲
DANGER
! Roadside wheel changing is hazardous. Be extra vigilant, you may not be able to avoid jacking on tarmacadam. Get
everyone
out of vehicle. NEVER go under vehicle. Traffic may cause vehicle to rock. Use hazard warning lights. If in doubt call
professional help.
9
When changing a wheel, loosen wheel nuts/bolts slightly prior to jacking vehicle. Screw wheel nuts/bolts back before lowering vehicle.
9
T
ighten finally when vehicle is lowered fully.
9
U
se a qualified person to lubricate and maintain the jack. Confirm that only recommended hydraulic jack oil is used during maintenance.
8
DO NOT
exceed the rated capacity of the jack and
DO NOT
operate the jack beyond its maximum pump stroke.
WARNING!
DO NOT
allow the vehicle to move, or try to start the engine, when the vehicle is jacked up.
8
DO NOT
jack a vehicle if it may result in the spillage of fuel, battery acid, or other dangerous substances.
8
DO NOT
place any part of your body under vehicle whilst it is supported by the jack. Wait until adequately rated axle stands have been
correctly positioned.
8
DO NOT
use jack to support extensions or cradles.
DO NOT
modify jack in any way.
DO NOT
use the jack for any other purpose.
8
DO NOT
top up jack with brake fluid. Use Sealey hydraulic oil only (Part No: HJO500MLS or HJO5LS).
8
DO NOT
allow untrained persons to operate the jack.
8
DO NOT
remove any labels from the jack. If labels are damaged or unclear, replace them.
8
DO NOT
operate the jack when you are tired, under the influence of alcohol, drugs or intoxicating medication.
9
Ensure there are no persons or obstructions beneath the vehicle before lowering.
9
Clean and securely stow the jack with the ram in the down position.
DO NOT
leave the ram extended.
9
When not in use, store the jack in a safe, dry, childproof area.
WARNING!
Remember, it is very dangerous to go under a vehicle supported by a jack even if additional supports are used.
8
DO NOT
go under a vehicle unless it is supported by adequately rated axle stands. NOTE: Seek advice before jacking caravans or
trailers.
2. INTRODUCTION
F
ully tested and fitted with overload valve to comply with the latest CE directives. Base and reservoir machine welded for increased strength
and reduced chance of leakage. Threaded pump assembly allows for easy disassembly and maintenance. Supplied with 2pc handle.
M
odel No’s SJ12 to SJ30 fitted with carrying handle. Service kits readily available.
3. SPECIFICATION
In the table below the dimensions are cross-referenced to (fig.1).
Model: . . . . . . . . . . . . . . . . . . . . . . . . . SJ2 . . . . . . SJ3 . . . . . .SJ5 . . . . . . SJ8 . . . . .SJ10. . . . . SJ12 . . . . . SJ15. . . . . SJ20 . . . . . SJ30
Capacity tonnes . . . . . . . . . . . . . . . . . . . . .2 . . . . . . . .
3
. . . . . . . .5 . . . . . . . . 8 . . . . . . .
10
. . . . . . .
12
. . . . . . .
15
. . . . . . . .20 . . . . . . .
30
Minimum Height mm (A)
. . . . . . . . . . . . .
168
. . . . . .
188
. . . . . .207 . . . . . . 222 . . . . . . 222. . . . . . 227 . . . . . . 227. . . . . . .
235
. . . . . . 260
Hydraulic Lift mm (B)
. . . . . . . . . . . . . . .
100
. . . . . .
115
. . . . . .
125
. . . . . .
145
. . . . . .
145
. . . . . .
150
. . . . . .
150
. . . . . . .
150
. . . . . .
160
Screw Extension mm (C) . . . . . . . . . . . . .
48
. . . . . . . 60 . . . . . . .70 . . . . . . . 80 . . . . . . . 80. . . . . . . 80 . . . . . . . 80. . . . . . . .60 . . . . . .n/a
Maximum Height mm (D)
. . . . . . . . . . . .
316
. . . . . .
363
. . . . . .
402
. . . . . .
447
. . . . . .
447
. . . . . .
457
. . . . . .
457
. . . . . . .
445
. . . . . .
420
S
J Series | Issue 2 (F,2,3) 24/06/19
Original Language Version
© Jack Sealey Limited
Refer to
instructions
