1/4”& 3/8”SQ DRIVE SUPER STUBBY AIR
RATCHET WRENCH
MODEL NO’S
:
SA632.V2 & SA633.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9
Follow all workshop safety rules, regulations, and conditions when using wrench.
WARNING!
Disconnect from air supply before changing accessories or servicing.
WARNING! DO NOT
use wrench if damaged or thought to be faulty. Contact Service Agent.
WARNING!
Check correct air pressure is maintained and not exceeded. We recommend 90psi.
9
Maintain the wrench in good condition and replace any damaged or worn parts. Use genuine parts only. Un-authorised parts may be
dangerous and will invalidate the warranty.
9
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are
secure.
9
Wear approved safety eye/face shield, ear defenders and hand protection.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and non essential persons away from the working area.
8
DO NOT
use the wrench for a task it is not designed to perform.
8
DO NOT
use wrench unless you have been instructed in its use by a qualified person.
8
DO NOT
carry the wrench by the air hose, or yank the hose from the air supply.
8
DO NOT
operate wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
carry wrench with your hand on power trigger, in order to avoid unintentional starting.
8
DO NOT
direct air from the air hose at yourself or others.
When not in use disconnect from air supply and store in a safe, dry, childproof location.
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into
this product, but must be applied by the operator.
2.
i
INTRODUCTION
U
ltra-compact air ratchet wrenches fit in the palm of the hand. Perfect for working around tightly-packed engine compartments. Ratchet yoke
designed and manufactured to provide additional strength. Rear exhaust with baffle reduces noise.
3.
i
SPECIFICATION
Model No’s:.................................... ....... SA632.V2/SA633.V2
Air Consumption:......................................................... 2.4cfm
Drive: ........................................................... 1/4”Sq. / 3/8”Sq.
Free Speed: ...............................................................250rpm
Inlet size: ...................................................................
1/4”BSP
Length: ....................................................................... 140mm
Maximum Torque: ............................................. 25lb.ft(34Nm)
N
oise Power/pressure:
.................. 101/91dB(A) / 99/89dB(A)
O
perating Pressure:
...................................................... 90psi
Vibration/Uncertainty: ......................................... 4.4/1.86m/s²
4. AIR SUPPLY
4.1.
AIR SUPPLY
(Recommended hook-up procedure is shown in fig.2.)
4.1.1.
Ensure wrench air valve (or trigger) is in the “off” position before connecting to the air supply.
4.1.2.
You will require an air pressure of 90psi, and an air flow according to specification.
WARNING!
Ensure the air supply is clean and does not exceed 90 psi while operating the wrench. Too high an air pressure and/or
unclean air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
4.1.3.
Drain the compressor air tank daily. Water in the air line will damage the wrench.
4.1.4.
Clean compressor air inlet filter weekly.
4.1.5.
Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should be
1/4” I.D. and fittings must have the same inside dimensions.
4.1.6.
Keep the hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all connections are secure.
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Wear protective
gloves
Wear eye
protection
Wear face
mask
Wear ear
protection
SA632.V2, SA633.V2 Issue 3 (H, F) 26/10/21
