3/8” / 1/2” SQ DRIVE AIR RATCHET WRENCH
MODEL NO:
SA607.V2, SA608.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
1. SAFETY
9
Follow all workshop safety rules, regulations, and conditions when using wrench.
WARNING!
Disconnect from air supply before changing accessories or servicing.
9
Maintain the wrench in good condition and replace any damaged or worn parts. Use genuine parts only. Non-authorised parts
may be dangerous and will invalidate the warranty.
WARNING!
Check correct air pressure is maintained and not exceeded. We recommend 90psi.
9
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
9
Only use impact sockets which are specifically designed for use with a ratchet wrench.
9
Wear approved safety eye/face shield, ear defenders, and hand protection.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and non essential persons away from the working area.
8
DO NOT
use the wrench for a task it is not designed to perform.
WARNING! DO NOT
use wrench if damaged or thought to be faulty. (Contact Service Agent).
8
DO NOT
use wrench unless you have been instructed in its use by a qualified person.
8
DO NOT
expose the comfort grip to excessive heat.
8
DO NOT
carry the wrench by the air hose, or yank the hose from the air supply.
8
DO NOT
operate wrench if you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
carry wrench with your hand on the power trigger in order to avoid unintentional starting.
8
DO NOT
direct air from the air hose at yourself or others.
9
When not in use disconnect from air supply and store in a safe, dry, childproof location.
2. INTRODUCTION
C
omposite cover moulded around lightweight aluminium alloy housing reduces effects of chill on operator’s hands and provides added control.
Air motor with quality bearings for smooth and powerful operation. Exhaust outlet adjusts 360°, keeping airflow away from operator. Features
twist-reverse action and trigger operated power control. Hardened gear and yoke assembly ensures suitability for the professional workshop.
3. SPECIFICATION
4. PREPARATION
4.1.
AIR SUPPLY
WARNING!
Ensure the air supply is clean and does not exceed 90 psi while operating the die wrench. Too high an air pressure and
unclean air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
4.1.1. Recommended hook-up procedure is shown in fig.1.
Ensure wrench air valve (or trigger) is in “off” position before connecting to the air supply.
4.1.2. You will require an air pressure of 90psi, and an air flow according to specification.
4.1.3. Drain the air tank daily. Water in the air line will damage the wrench.
4.1.4. Clean air inlet filter weekly.
4.1.5. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should be
1/4” I.D. and fittings must have the same
inside dimensions.
4.1.6. Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all connections are secure.
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear ear
protection
MODEL No:
SA607.V2
SA608.V2
Drive size
3/8”Sq
1/2”Sq
Max torque
50lb.ft (68Nm)
50lb.ft (68Nm)
Air consumption
4cfm
4cfm
Operating pressure
90psi
90psi
Inlet size
1/4”BSP
1/4”BSP
Vibration/Uncertainty
0.44/0.22m/s²
0.44/0.22m/s²
Noise Power / Pressure
85/83dB.A
84/83dB.A
Free Speed
200rpm
200rpm
S
A607.V2, SA608.V2 Issue 2 (H,F) 06/08/21
Wear face
mask
