background image

AIR RIVETER 1/4” STEEL ALUMINIUM, ALLOY 

& STAINLESS STEEL RIVETS

MODEL NO:

 SA314.V4

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, 

and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  SAFETY

 

‰

   WARNING!

 

Ensure health & safety, local authority, and general workshop practice regulations are adhered to when using this  

 

 equipment.

 

9

   Familiarise yourself with this products application and limitations, as well as the specific potential hazards peculiar to the riveter.

 

‰

  

WARNING!

 Disconnect the riveter from the air supply before changing accessories, servicing or performing any maintenance.

 

9

   Maintain  the

 

riveter in good condition (use an authorised service agent).

 

9

   Replace or repair damaged parts. 

Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

 

9

   Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.

 

9

   Keep the riveter clean for best and safest performance.

 

‰

  

WARNING! 

Always wear approved eye (or face) and hand protection when operating the riveter.  

 

9

   Maintain correct balance and footing. 

DO NOT

 over reach, ensure the floor is not slippery, wear non slip shoes.

 

9

   Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain and/ or tie back long hair.

 

9

  

Wear appropriate protective clothing and keep hands and body clear or working parts.

 

9

   Keep the riveter away from your body and at a safe distance from others.

 

9

   Keep children and unauthorised persons away from the working area.

 

9

   Secure non stable work piece with a clamp, vice or other adequate holding device. 

 

9

   Ensure that spent rivet stems are disposed of correctly and 

DO NOT

 cause a hazard.

 

‰

  

WARNING!

 Ensure correct air pressure is maintained and not exceeded. Recommended pressure 90psi.

 

9

   Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use, and ensure that all connections are    

 secure.

 

8

  

DO NOT

 use the riveter for a task it is not designed to perform.

 

8

  

DO NOT

 operate the riveter if any parts are damaged or missing as this may cause failure and/or personal injury.

 

9

   Ensure the safety cap is correctly fitted.

 

8

  

DO NOT

 carry the by the hose, or yank the hose from the air supply.

 

8

  

DO NOT

 get the riveter wet or use in damp or wet locations or areas where there is condensation.

 

8

  

DO NOT

 allow untrained persons to operate the riveter.

 

8

  

DO NOT

 operate the riveter when you are tired, under the influence of alcohol, drugs or intoxicating medication.

 

8

  

DO NOT

 direct air from the air hose at yourself or others.

 

9

   When not in use disconnect from the air supply and store in a safe, dry, child proof location.

 

9

  

Avoid unintentional starting.

2.  INTRODUCTION

i

Suitable for aluminium, steel and stainless steel up to 3/16”. Supplied with four riveting nozzles and two spanners. Trigger operated riveter with 

hardened jaw assembly and rivet shaft safety cap. Will handle heavy assembly work.

3.  SPECIFICATION

Model no: .................................................................... SA314

Nozzle sizes:

 .............................. 3/32” (2.4mm), 1/8” 3.2mm, 5/32” (4mm), 

 .................................................. 3/16” (4.8mm), 1/4” (6.4mm)

Air consumption: ....................................................... 3.46cfm

Operating pressure: ...................................................... 90psi

Air inlet size:..............................................................1/4”BSP

Weight: .......................................................................... 1.6kg

Blind rivet type: ....................aluminium, steel, stainless steel

Noise power/pressure: ......................................... 81/70dB(A)

Vibration: .................................................................. 10.9m/s²

Uncertainty: .............................................................. 4.36m/s²

SA314.V4    Issue: 2(H,F)  01/06/18

Original Language Version

© Jack Sealey Limited

Refer to 

instruction

manual

Wear eye 

protection

Wear ear 

protection

Wear protective 

gloves

Отзывы: