Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
2. INTRODUCTION & SPECIFICATIONS
1. SAFETY INSTRUCTIONS
2.1
INTRODUCTION
Economy Range suitable for the serious enthusiast or occasional professional use. Made from high quality steel with a powder coated paint
finish to help corrosion resistance.
2.2
SPECIFICATION
1.1
GENERAL SAFETY
Familiarise yourself with this products application and limitations, as well as the specific potential hazards peculiar to the press.
Maintain the
press in good condition (use an authorised service agent).
Replace or repair damaged parts.
Use recommended parts only. Non authorised parts may be dangerous and will invalidate the warranty.
Keep the press clean for best and safest performance.
Locate the press in a suitable working area for its function, keep area clean, tidy, free from unrelated materials and ensure there is
adequate lighting.
Ensure the workpiece is correctly secured before operating the press.
WARNING!
Always wear approved eye or face protection when operating the press.
Remove ill fitting clothing. Remove ties, watches, rings, loose jewellery and contain long hair.
Keep hands and body clear of the work table when operating the press.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip steel toe-capped shoes/boots.
Keep children and unauthorised persons away from the working area.
DO NOT
operate the press if any parts are missing as this may cause failure and/or possible personal injury.
DO NOT
use to compress springs or any other item that could disengage and cause a potential hazard.
DO NOT
stand directly in front of the loaded press and never leave a loaded press unattended.
DO NOT
use the press for any purpose other than that for which it is designed.
DO NOT
make any modifications to the press.
DO NOT
adjust or tamper with the safety valve.
DO NOT
exceed the rated capacity of the press.
DO NOT
apply off-centre loads.
DO NOT
allow the workpiece or the press plates to fall from the work table.
DO NOT
get the press wet or use in damp or wet locations or areas where there is condensation.
DO NOT
operate the press when you are tired or under the influence of alcohol, drugs or intoxicating medication.
When not in use, release pressure from the hydraulic unit and clean the press. Stand or store the press plates in a safe location.
WARNING! Always position the press against a wall. If the press is situated in the open workshop, it is essential that a guard be
placed at the rear of the unit. This will prevent injury to bystanders in the event of the workpiece ejecting suddenly.
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this
product, but must be applied by the operator.
DANGER! The press is heavy.
If it requires moving after assembly or for relocation, use suitable slings around the top crossbeam, or
lift direct with a forklift with the forks located under the top crossbeam. If a forklift is not available we suggest a minimum of two people are
required to lift and move the press.
Model:
YK6ECB
Bench or Floor Mounting
Bench
Type:
Hydraulic
Capacity:
6tonne
Ram Stroke:
125mm
Ram Ø:
20mm
Maximum Height - Ram to Table:
245mm
Minimum Height - Ram to Table:
0mm
Table Aperture:
65mm
Work Table Depth:
145mm
Work Table Width:
340mm
Overall Height:
935mm
Gauge Included:
No
Weight:
26.4kg
INSTRUCTIONS FOR:
Hydraulic Press 6tonne Economy
Bench Type
Model No:
YK6ECB
YK6ECB Issue No: 1 - 16/07/12
Original Language Version
© Jack Sealey Limited 2012
