instructions for
professional pressure washer 150Bar
with tss and nozzle set 230V
model no:
pw5000
thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. safetY
1.1.
eleCtriCal safetY
warninG!
it is the user’s responsibility to check the following:
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and all
electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey stockist.
if the pressure washer is used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable
Appliance test) tested.
electrical safety information, it is important that the following information is read and understood.
1.1.1.
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
important
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct
fuse - see fuse rating in these instructions.
8
do not
pull or carry the appliance by the power cable.
8
do not
pull the plug from the socket by the cable.
8
do not
use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired
or replaced immediately by a qualified electrician.
1.1.3.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
if the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
General safetY
warninG!
Water and electricity are dangerous partners
.
Be extremely cautious
and
alwaYs
be aware that this device uses an
electric motor. Always plug into a rcd (see electrical safety above). unplug from mains before changing accessories or servicing.
warninG! do not
use the washer if any part of the unit, gun, nozzle, detergent tank, hose or cables is damaged. replace or repair
using genuine parts only. unauthorised parts may be dangerous and will invalidate your warranty. Always check connections
are correctly secured and not cracked or damaged in any way before using the machine.
8
warninG!
use washer on a flat, level surface, in an upright position. failure to do so will invalidate your warranty.
neVer
lay the washer down during use.
9
ensure you comply with all local water supply regulations. Power washers may only be connected to mains water supply if a check valve
is installed in the supply hose, or at the tap outlet
.
9
The supply hose must be reinforced, and have an internal diameter of 1/2” (13mm). The water supply must be at least equal to the
cleaner capacity. the water temperature must
not
exceed 122°F (60°C). The water supply pressure must
not
exceed 6 bar (90psi).
9
9
99
Always be aware
of the hazards that may occur
during use. study all applications and limitations of the washer before use.
9
9
99
use where air can freely circulate around the washer to avoid the machine overheating.
9
Keep the washer in good condition. use an authorised service agent to service the unit.
9
9
99
Wear adequate protective clothing, goggles and anti-slip rubber soled footwear.
9
Position the washer as near to the water supply as possible.
9
99
warninG!
ensure all persons and animals keep at a minimum distance of 15mtr from the washer when in use.
9
99
warninG!
the pressure washer must only be used with clean water. unfiltered water or corrosive chemicals must not be used as
these will damage the cleaner.
9
ensure the nozzle is aimed correctly at the work surface before switching the machine on.
9
Before activating the trigger, grip the gun firmly to counteract the recoil from the high pressure water jet.
9
99
warninG!
Avoid sudden bursts of water as these will cause water pressure to drop and put extreme pressure on hoses and
connectors.
9
if, during operation, power failure occurs turn the electricity and water off for safety reasons.
P
W5000 | Issue:2(L) 11/04/17
Original Language Version
© Jack sealey limited
refer to
instruction
manual
Wear eye
protection
Wear ear
protection
Wear safety
footwear
Wear protective
clothing
recommended fuse rating
13 Amp
