3TONNE CAR LIFT/RAMP
MODEL NO.:
MR1
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
i
WARNING!
Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
WARNING! TRAPPING DANGER
Keep hands and limbs away from the steelwork during elevating and lowering.
WARNING!
Prepare the vehicle ready for both when moving onto, and at rest, on the ramp. Ensure the vehicle will not move, tip, fall etc.
WARNING! DO NOT
use the ramp to support, hold or move a vehicle which is unstable.
NOTE:
It is recommended that two people are used to assemble the unit.
8
DO NOT
operate the ramp if damaged.
8
DO NOT
allow untrained persons to assemble or operate the ramp.
8
DO NOT
exceed the rated capacity of the ramp.
8
DO NOT
allow the vehicle to move on the ramp.
8
DO NOT
move vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
8
DO NOT
climb on the ramp.
8
DO NOT
use the ramp for purposes other than that for which it is intended.
8
DO NOT
modify the ramp.
8
DO NOT
use to achieve a task that the vehicle ramp was not designed to perform.
8
DO NOT
drive onto or off ramp with passengers inside vehicle.
8
DO NOT
exceed total load capacity of 3.0 tonne (1800 kg single axle weight). Refer to vehicle manual for weight of vehicle.
8
DO NOT
operate the vehicle ramp if parts are damaged or missing as this may cause failure and/or personal injury.
9
Keep the work area clean, uncluttered and ensure there is adequate lighting.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip protective footwear.
9
Remove ill-fitting clothes. Remove ties, watches, rings, other loose jewellery.
9
Familiarise yourself with the applications, limitations and potential hazards of the vehicle ramp.
9
Use on a hard, level non-slippery surface such as concrete that is capable of supporting the load of the vehicle and the ramp. Avoid
tarmacadam as ramp may sink in.
9
Ensure the ramp is in sound condition and good working order. Take action for immediate repair or replacement of damaged parts. Use
genuine parts only. The use of non-standard parts may be dangerous and will invalidate the warranty.
9
Once the load is mounted it is imperative that the vehicle is secured in place using chocks and that the ignition key is withdrawn
from the switch.
9
Check the load is stable on the ramp, make sure there is no risk of tilting or slipping.
9
When mounting or lowering a car
DO NOT
allow anyone other than the operator to approach the work area.
9
Ensure adequate level space around the vehicle for the operator and the ramp.
9
Ensure there are no passengers in the vehicle.
9
Ensure all non-essential persons keep a safe distance from the ramp whilst it is in use.
9
Ensure you have a clear view and necessary assistance when ascending/descending the ramp.
9
Ensure there are no persons or obstructions beneath the vehicle before moving.
9
When not in use store the ramp in a safe, dry, childproof area.
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into
this product, but must be applied by the operator
2. INTRODUCTION
Compact, convenient and innovative 3tonne (pair) rated car ramps (maximum single axle weight of 1800kg), supplied with four stands and
removable lifting beam, capable of raising a vehicle completely off the ground giving a clear workspace between vehicle and floor. Designed
so the track width can be adjusted to fit various makes and model of cars with maximum tyre width of 380mm. Excellent for general servicing,
exhaust work repairing damaged jacking points, sills, floor panels and undersealing. Will fit within confined areas such as garages and
workshops. Safe and efficient operation, gives a clear workspace between the raised vehicle and floor. Requires a jack with a saddle height no
taller than 100mm, a maximum diameter of 120mm and max. jacking height of 435mm to lift its jacking beam to a position where its stands can
be inserted.
MR1 Issue 1 02/11/2020
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Wear
protective
gloves
Wear
protective
footwear
