background image

Unpack the lift and check contents with list below. Should there be any damaged or missing parts contact your supplier immediately. 

Content

• Main Assembly

• Sliding Plate

• Leading Plate

• Vice

• Lifting Pedal

• Release Pedal

• Pedal Guard

• Bolts, Washers, Nuts, Cotter Pins

p

p

 

 

WARNING!

Keep your hands away from moving parts.

Numbers in brackets refer to item numbers in the parts diagram.
3.1.

Assembly

3.1.1.  Fit the sliding plate (66) to the platform (60), to cover the rear wheel removal aperture.

3.1.2.  Attach leading plate (69) to end of platform (60) using washers (49) and cotter pins (70).

3.1.3. Fit the front wheel vice assembly (64) to the front of the platform (60) using bolts (65),

washers (49) and nuts (33).

3.1.4. Insert the lift foot pedal (71) into the pump piston spindle (10) and insert the 

release foot pedal (72) into the release valve spindle (5).

3.1.5. Attach the guard plate (67) to the frame (44A) using bolts (68) and nuts (P23). This guard covers the release foot pedal to minimise the 

risk of accidental lowering.

3.1.6. An extension plate (77) is provided for longer wheelbase bikes. Attach this to the front end of the main platform using the screws (75) 

and the nuts (76).

3.2.

Before first use

3.2.1. Leave the pump for one hour, to allow the oil to settle, before purging the system.

Note:

Failure to allow sufficient time for the oil to settle could result in air remaining in the oil. In this event, the pump will not purge 

completely first time and a second purge will be required.

3.2.2. Purge the hydraulic circuit, to eliminate any air in the system, by fully pressing the release valve pedal (72) and pumping the lift pedal 

(71) 15 to 20 times.

3.2.3. Test the lift, unladen, by raising it to full height and then lowering it. Depress release valve pedal (72) slowly to control the rate of descent.

INSTRUCTIONS FOR:

400KG HYDRAULIC MOTORCYCLE LIFT

Model:  

MC401

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly

maintained, give you years of trouble free performance.

1. SAFETY INSTRUCTIONS

2. SPECIFICATION

3

Maintain the lift in good condition (use an authorised service agent).

3

Replace or repair damaged parts. 

Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

3

Use a qualified person to lubricate and maintain the lift. 

DO NOT

use brake fluid to top up hydraulic unit.

3

Locate the lift in a suitable work area. Keep area clean and tidy and free from unrelated materials, and ensure that there is adequate lighting. 

3

Ensure that the floor is level and strong enough (preferably concrete) to take the weight of the lift and the bike.

DO NOT

operate the lift on 

tarmacadam, as the surface may be unstable.

3

Keep the lift clean for best and safest performance.

3

Before use, stabilise the lift by turning the foot stops so that the lift is just raised off of its wheels.

3

The maximum bike weight is 400kg. 

DO NOT

exceed this rated capacity.

3

Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain long hair.

3

Maintain correct balance and footing, do not over reach. Ensure the floor is not slippery and wear non-slip shoes.

3

Ensure the bike is adequately secured to the lifting platform with appropriate straps. 

3

Before lifting check that there are no overhead obstructions.

3

When platform has been raised to the working height ensure that the platform safety spindle is fitted to prevent accidental lowering.

3

Keep children and unauthorised persons away from the work area.

3

The lowering speed will vary according to the weight of the load and the release valve setting.

7

DO NOT

use the lift for a task it is not designed to perform.

7

DO NOT

operate the lift if it is damaged.

7

DO NOT

exceed the rated capacity of the lift.

7

DO NOT

operate the lift when you are tired or under the influence of alcohol, drugs or intoxicating medication.

7

DO NOT

allow untrained persons to operate the lift.

7

DO NOT

attempt to transport a load on the lift. The lift must only be used in a static position for raising and lowering loads.

7

DO NOT

make any modifications to the lift and 

DO NOT

adjust or tamper with the safety valve.

3

Before lowering the lift ensure that there are no obstructions underneath the platform and that all persons are standing clear.

3

Before storing in safe area, ensure that all parts are clean and free of grease and oil. Store lift fully lowered.

IMPORTANT:

PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.

USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE

DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

3. ASSEMBLY

Specification

Capacity . . . . . . . . . . . . . . . . . . . . . .400kg

Minimum Height  . . . . . . . . . . . . . . .180mm

Maximum Height  . . . . . . . . . . . . . .760mm

MC401 - 5 -130104

Содержание MC401

Страница 1: ...e lift DO NOT use brake fluid to top up hydraulic unit 3 Locate the lift in a suitable work area Keep area clean and tidy and free from unrelated materials and ensure that there is adequate lighting 3 Ensure that the floor is level and strong enough preferably concrete to take the weight of the lift and the bike DO NOT operate the lift on tarmacadam as the surface may be unstable 3 Keep the lift c...

Страница 2: ...is believed to have been subjected to abnormal load or shock Inspect and take appropriate action 5 4 Periodically check the ram and piston for signs of corrosion Clean exposed areas with a clean oiled cloth 5 5 The hydraulic oil level is checked as follows 1 Remove hydraulic unit from lift and stand upright 2 Remove vented plug fig 1 A Correct oil level is up to plug aperture add hydraulic oil as ...

Страница 3: ...escription 49 MC401 049 Washer 50 MC401 050 Bolt M10 x 16 51 MC401 051 Return Spring 52 MC401 052 Back Lifting Arm 53 MC401 053 Lifting Arm Spindle 54 MC401 054 Bolt 55 MC401 055 Bush 56 MC401 056 Bolt M12 x 65 57 MC401 057 Washer 58 MC401 058 Nut M12 59 MC401 059 Front Lifting Arm 60 MC401 060 Platform 61 MC401 061 Bush 63 MC401 063 Bolt M12 x 40 64 MC401 064 Vice 65 MC401 065 Bolt M10 x 25 66 MC...

Страница 4: ...Kempson Way Suffolk Business Park Bury St Edmunds Suffolk 1P32 7AR and was undertaken by Changshu Tongrun M E Co Ltd the manufacturer of the product in China and the holder of the construction file This certificate is signed by the Chief Engineer for the manufacturer We hereby certify that the motorcycle lift covered by this test certificate has been tested to 25 overload and the safety valve has ...

Отзывы: