INSTRUCTIONS FOR:
CREE LED ALUMINIUM TORCH 10W
RECHARGEABLE LITHIUM-ION WITH
ADJUSTABLE FOCUS
Model No
: LED034
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you
years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1. GENERAL.
Ensure the torch is correctly charged before initial use.
DO NOT
turn the torch on when it is being charged.
DO NOT
shine directly into your, other person’s or animal’s eyes.
DO NOT
allow children to use the torch.
DO NOT
use the torch if you suspect that the battery or the torch casing is damaged.
DO NOT
immerse the torch in water.
When not in use store the torch a safe, dry, childproof location.
1.2. ELECTRICAL SAFETY.
USE ONLY THE SUPPLIED MAINS CHARGER PLUG FOR CONNECTING TO THE MAINS POWER SUPPLY.
WARNING!
It is the user’s responsibility to read, understand and comply with the following electrical instructions:
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An RCCB (Residual Current Circuit
Breaker) should be incorporated in the main distribution board. We also recommend that an RCD (Residual Current Device) is used with
all electrical products, particularly portable equipment which is plugged into an electrical supply not protected by an RCCB.
You must
also read and understand the following instructions concerning electrical safety.
1.2.1.
The Electricity At Work Act 1989
requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.2.2
. The Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of the appliance
and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.2.3.
You must ensure that you:
Inspect the charger plug, cable and connector for wear and damage to ensure items are safe before connecting to the mains power
supply. If worn or damaged
DO NOT
use.
Check cables are always protected against short circuit and overload.
IMPORTANT:
Check that the voltage marked on the charger plug is the same as the power supply to be used.
DO NOT
pull the charger plug from the mains socket by the lead.
DO NOT
use any other type of charger with this product.
DO NOT
try to take the charger plug apart.
DO NOT
use the charger plug to charge or power any other electrical item.
DO NOT
get the charger wet, or use in wet, damp conditions (for indoor use only).
WARNING!
NEVER
substitute a standard 13 Amp 3 pin plug, or any other type of plug, for the charger plug.
Original Language Version
LED034 Issue: 1 - 11/04/13
2. INTRODUCTION & SPECIFICATION
Single 10W CREE LED produces extremely bright, white light with an output of over 350 lumens, and gives a working range up to 500 metres.
Illumination type can be changed from spotlight to wide area by simple push/pull action of the head. Features lightweight Aluminium housing. Five
function on/off push-button for full, half, low, flashing and SOS light. Powered by a 3.7V 2.0Ah Li-ion rechargeable battery. Supplied with 3 pin
mains charger/adaptor.
Fig.1
© Jack Sealey Limited
Model No:
LED034
Cell Type:
3.7V 2.0Ah Ll-ion Rechargeable
Lumen Output:
350lm
LED:
10W
CREE
Charging Time:
4 hours
Operating Time:
2 hours
Multi function switch
Linear beam adjustment
