background image

INSTRUCTIONS FOR: 

GALVANIZED SHED GREEN 

2.3 X 2.3 X 1.9m 

MODEL NO:

 GSS2323G

IMPORTANT:

 

PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.  USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these 

instructions, and properly maintained, give you years of trouble free performance.

 1.  SAFETY

 2. INTRODUCTION

 3. SPECIFICATION

 4. CONCRETE PLINTH SLAB

 

 

WARNING!

 Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when building this shed.

 

Keep the work area clean, uncluttered and ensure there is adequate lighting.

 

Keep children and unauthorised persons away from the working area.

 

DO NOT

 use the shed for any purpose other than that for which it is designed.

 

Use appropriate safety clothing including eye protection.

 

 

DO NOT

 attempt to assemble in windy weather.

 

  

Note:

 The assembly of this product will require assistance.

Galvanized steel panels easily assembled to form a rigid and secure gable roofed shed. Has a single door  which is secured by cross bolt and 

eyelet that accepts a padlock (not included) for additional security. Supplied with bolt-down fixing kits.

Model No:  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GSS2323G

Overall Size (W x D x H*):  . . . . . . . . . . . . . . . . . . . 2300 x 2300 x 1900mm

Roof Type:  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gable

*Minimum Wall Height

Concrete slab: Please ensure that your site is level. It is recommended that your slab is 100mm thick and you use builders plastic and F52 

reinforcing mesh. We recommend that you make your slab 100mm bigger than the base dimensions of your shed. This will allow for a 50mm edge 

around your shed. We recommend that you slope the 50mm edges downward by 10 mm so that rain water will drain away from your shed.

  GSS2323G   Issue: 1 - 28/08/14

Original Language Version

 © Jack Sealey Limited

Содержание GSS2323G






















Отзывы: