Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instruction
manual
Wear eye
protection
Keep away
from rain
Wear
protective
gloves
Use in well
ventilated
areas
Keep sources
of ignition away
from vehicle
battery: risk of
explosion
1. SafeTy
Modern vehicles contain extensive electronic systems.
You are required to check with the vehicle manufacturer, for any specific instructions regarding the use of this type of
equipment on each vehicle. No liability will be accepted for damage/injury, where this product is not used in accordance
with all instructions.
9
Ensure that the vehicle is in a well ventilated area.
9
Apply the handbrake and select neutral or ‘park’ before attempting to start.
9
Ensure that the ignition switch and all ancillary electrical equipment is switched off.
9
Keep clear of any pulleys, belts etc. that will move once the engine starts.
9
Take care to ensure correct connection polarity; red clamp to positive, black clamp to negative.
9
Energise the E/START1600.V2 only at ambient temperatures between -30°C and 40°C.
9
When not in use, switch off and store in a cool, dry place out of the reach of children.
8
DO NOT
allow this power pack to become wet.
8
DO NOT
dismantle this E/START1600.V2, there are no user serviceable parts inside.
8
DO NOT
use in explosive atmospheres (e.g. the presence of flammable liquids, gases or dust).
8
DO NOT
use the E/START1600.V2 if it appears damaged in any way.
8
DO NOT
leave in direct sunlight or expose to heat.
8
DO NOT
use abrasive or solvent cleaners on this product.
8
DO NOT
allow children to play with this product
1.1.
CHaRGING SafeTy INSTRUCTIONS
9
Familiarise yourself with the application and limitations of the charger as well as the potential hazards. Also refer to the vehicle
manufacturer’s hand book.
9
Ensure the charger is in good condition before use. If in any doubt do not use the unit, contact your Sealey stockist.
9
Ensure that the starter/charger is placed on a stable surface which will adequately support its weight.
9
Keep tools and other items away from the engine and ensure you can see the battery and working parts of engine clearly.
9
Ensure the output of the charger is the same voltage as the battery.
9
Ensure that, during charging, the charger is placed in a location where there is sufficient ventilation to prevent the build up of explosive
gases from the vehicle’s lead acid battery.
9
If battery has caps to access the battery fluid, remove the caps and check the fluid level. Replace caps before connecting the power
clamps.
9
If necessary top-up the battery with distilled water by referring to the battery manufacturer’s instructions. If the charger receives a sharp
knock the unit must be checked by a qualified service agent before using.
9
If the battery terminals are corroded or dirty, clean them before attaching the power clamps.
9
Keep children and unauthorised persons away from the working area.
8
DO NOT
try to charge a non-rechargeable battery.
8
DO NOT
try to charge battery if battery fluid is frozen.
8
DO NOT
allow power clamps to make contact with any metallic part of the vehicle.
8
DO NOT
cross connect power leads from charger to battery. Ensure positive (+/RED) is to positive and negative (-/BLACK) is to negative.
8
DO NOT
pull the cables or clamps from the battery terminals.
8
DO NOT
use the charger in wet locations and
DO NOT
operate within the vicinity of flammable liquids or gases.
8
DO NOT
use the charger for a task for which it is not designed.
WaRNING! DO NOT
simultaneously charge batteries of different capacities or discharge levels.
WaRNING!
If a fuse blows, ensure it is replaced with an identical fuse type and rating. Use only Sealey genuine parts.
2. INTRODUCTION
Vehicle jump starting made easy with innovative patented technology. Unlike traditional boosters, it has no internal batteries, as it uses
ultracapacitors to maximise the discharged battery’s voltage. Simply connect to the vehicle’s battery, even if discharged, and the unit will draw
enough power to energise itself in a matter of minutes. Power can then be pushed safely back through the starting system to jump start the
vehicle. If the vehicle’s battery is faulty or holding less than 5 volts, the ElectroStart® range can be pre-charged via another vehicle’s battery or
the 12V accessory lead* (excludes Model No. E/START1224). The digital display indicates battery voltage, capacitor charge and faults. Safely
store the unit without the need for battery maintenance, and no delay waiting for a battery to charge, the device is ready for use within minutes.
Can also be used as a 0.8A battery maintainer using a USB charging cable or a 2A battery charger with the addition of Model No. E/START2A
Charging Adaptor. Compact and lightweight for easier handling and storage, yet still delivers the same result as heavy, bulky, lead acid battery
equivalents. Ideal for both professional mechanics and DIY users.
Original Language Version
© Jack Sealey Limited
Original Language Version
E/START1600.V2 Issue: 3 (5) - 29/04/19
eLeCTROSTaRT® BaTTeRyLeSS POWeRSTaRT
1600a 12V
MODEL NO:
e/STaRT1600.V2
