INSTRUCTIONS FOR:
DUAL ACTION SANDER
MODELS
:
DAS150T & DAS150T/DFS
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
DAS150T & DAS150T/DFS - 4 - 210405
IMPORTANT:
PLEASE READ INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
1.1.
Electrical Safety
p
p
WARNING!
It is the users responsibility to read, understand and comply with the following:
You must
check all electrical equipment and appliances to ensure they are safe before using.
You must
inspect power supply leads, plugs and all electrical connections for wear and damage.
You must
ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An
RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend
that an RCD (Residual Current Device) is used with all electrical products. It is particularly important to use
an RCD with portable products that are plugged into an electrical supply not protected by an RCCB.
If in doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your
Sealey dealer.
You must
also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises,
to be tested by a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the
appliance and the safety of the appliance operator. If in doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the mains power
supply. See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply leads and plugs for wear and damage and all electrical connections to
ensure that none is loose.
1.1.6. Important: Ensure the voltage marked on the product is the same as the electrical power supply to be
used and check that plugs are fitted with the correct capacity fuse. A 13 amp plug may require a fuse
smaller than 13 amps for certain products, see fuse rating below.
1.1.7.
DO NOT
pull or carry the appliance by the power supply lead.
1.1.8.
DO NOT
pull power plugs from sockets by the power cable.
1.1.9.
DO NOT
use worn or damaged leads, plugs or connections.
Immediately replace or have repaired by a qualified electrician.
A U.K. 3 pin plug with ASTA/BS approval is fitted. In case
of damage, cut off and fit a new plug according to the following
instructions, discard old plug safely (UK only - see diagram at right).
Ensure the unit is correctly earthed via a three-pin plug.
a) Connect the green/yellow earth wire to the earth terminal E.
b) Connect the brown live wire to live terminal L.
c) Connect the blue neutral wire to the neutral terminal N.
After wiring, check that there are no bare cores, that all wires
have been correctly connected, that the cable external insulation
extends beyond the cable restraint and that the restraint is tight.
Double insulated products are fitted with live (BROWN) and neutral
(BLUE) wires only. Double insulated products are always marked
with this symbol . Check your model carefully to see which type
of product your have. To re-wire a double insulated item, connect
the brown and blue wires as indicated above.
DO NOT
connect
brown or blue to the earth terminal.
1.1.10. Cable extension reels. When a cable extension reel is used it should be fully unwound before connection.
A cable reel with an RCD fitted is recommended since any product which is plugged into the cable reel
will be protected. The section of the cores of the cable is important and should be at least 1.5mm
2
, but to
be absolutely sure that the capacity of the cable reel is suitable for this product and for others that may be
used in the other output sockets, we recommend the use of 2.5mm
2
section cable.
p
WARNING!
Ensure Health & Safety, local authority, and general workshop practice regulations
are adhered to when using this equipment.
p
WARNING!
Disconnect from mains power before changing accessories or servicing.
Yellow & Green
Earth Wire
Brown
Live
Wire
Blue
Neutral
Wire
Cable
Restraint
01284 757500
01284 703534
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this equipment.
WARRANTY:
Guarantee is 12
months from purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our latest catalogue and
promotions call us on 01284 757525 and leave your full name and address, including postcode.
Sole UK Distributor, Sealey Group
, Bury St. Edmunds, Suffolk.
Declaration of Conformity
We, the sole importer into the UK, declare that the products listed here are in conformity
with the following standards and directives. The construction files for these products are held by the Manufacturer and may be
inspected, by a national authority, upon request to Jack Sealey Ltd.
For Jack Sealey Ltd. Sole importer into the UK
of Sealey Power Tools.
DUAL ACTION SANDER Models: DAS150T & DAS150T/DFS
73/23/EEC Low Voltage Directive
89/336/EEC EMC Directive
98/37/EC Machinery Directive
93/68/EEC CE Marking Directive
15th April 2003
Issue:
3
Date Issued:
210405
5. PARTS LIST
6. DECLARATION OF CONFORMITY
Signed by Mark Sweetman
FUSE RATING
THIS PRODUCT MUST BE
FITTED WITH A
5 AMP FUSE
ITEM PART NO.
DESCRIPTION
1
ER1700P/01
LOCKING CAP
2
ER1700P/02
LOCKING PIN
3
ER1700P/03
SPRING
4
ER1700P/04
GEAR HOUSING
5
ER1700P/05
BRASS BUSHING
6
ER1700P/06
RETAINING RING
7
DAS150T/07
SPIRAL BEVEL GEAR
8
DAS150T/08
RETAINING RING
9
B/6201ZZ
BEARING
11
DAS150T/11
BEARING BOX
12
DAS150T/12
SCREW PAN HD M4x16
c/w SPRING
13
ER1700P/12
WOODRUFF KEY
14
DAS150T/14
SPINDLE
14-1 DAS150T/14-1 SCREW M6
15
DAS150T/15
ALUMINIUM COVER
16
DAS150T/16
ECCENTRIC SHAFT
18
DAS150T/18
RETAINING RING
19-3 DAS150T.PSK
PAD SPINDLE KIT
(PARTS 17/19/19-1/19-2)
20
ER1700P/20
SCREW
21
ER1700P/21
NUT
22
DAS150T/22
PINION GEAR
23
B/6000ZZ
BEARING
24
ER1700P/24
BEARING COVER
25
ER1700P/25
SCREW
27
DAS150T/27
ARMATURE ASS'Y
28
B/608LLB
BEARING
28-1 DAS150T.28-1
O-RING
29
ER1700P/29
SCREW
30
DAS150T/30
FIELD ASS'Y
31
ER1700P/31
MOTOR HOUSING
32
ER1700P/32
SWITCH LEVER
33
ER1700P/33
CBON BRUSH HOLDER
34
ER1700P/34
CARBON BRUSH
35
ER1700P/35
CARBON BRUSH CAP
36
ER1700P/36
SWITCH BASE
37
ER1700P/37
SCREW
38
ER1700P/38
SWITCH
39
ER1700P/39
SCREW
40
ER1700P/40
STRAIN RELIEF
41
ER1700P/41
SCREW
42
ER1700P/42
SWITCH PULL ROD
43
ER1700P/43
SPRING
ITEM PART NO.
DESCRIPTION
44
ER1700P/44
CORD GUARD
46
CS 2.5M2CBLK POWER SUPPLY CORD
47
ER1700P/47
REAR COVER
48
ER1700P/48
SCREW
49
ER1700P/49
SIDE HANDLE
50
DAS150T/50
PAD
51
AK378/17S
17MM COMBI WRENCH
52
AK93-5
5MM HEX WRENCH
53
ER1700P/53-54 EMC PARTS
54
ER1700P/53-54 EMC PARTS
55
ER1700P/55
TERMINAL BLOCK
www.sealey.co.uk
Web
1.2.
General Safety
