INSTRUCTIONS FOR
CORDLESS IMPACT WRENCH 24V
1/2” SQ. DRIVE 325LB.FT
MODEL NO:
CP2400.V4
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. GENERAL SAFETY
Follow all workshop safety rules, regulations and conditions when using the wrench.
Remove the battery pack from the wrench before servicing or performing any maintenance.
Maintain the wrench and battery pack in good condition. Check moving parts for alignment on a regular basis.
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
Ensure the wrench is ‘locked’ before installing the battery pack.
Keep the wrench, battery pack and charger clean for optimum performance.
Keep the work area clean and tidy and free from unrelated materials. Ensure that there is adequate lighting.
Ensure that battery pack is correctly inserted into the wrench handle and latched in place before operating wrench.
R
WARNING!
When working around vehicle brake systems we recommend that you wear suitable respiratory protection due to the
possible presence of asbestos dust from brake linings.
Use only impact sockets which are specifically designed for use with an impact wrench.
Avoid unintentional starting.
Wear approved safety eye/face shield, ear defenders and hand protection.
Remove ill-fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Keep children and unauthorised persons away from the work area.
DO NOT
operate the wrench if any parts are missing as this may cause failure and/or personal injury.
DO NOT
use the wrench unless you have been instructed in its use by a qualified person.
DO NOT
operate the wrench where there are solvent fumes or flammable gases, liquids or solids.
DO NOT
leave the wrench operating unattended.
DO NOT
carry wrench with your finger on the trigger. Keep direction switch in ‘locked’ position when not in use.
DO NOT
use the wrench for a task it is not designed to perform.
DO NOT
operate the wrench when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT
get the wrench or battery charger wet or use in damp or wet locations.
Keep wrench and charger in the case and store in a safe, dry, childproof area where the temperature will not exceed 40°C (104°F).
1.2. Battery safety instructions
R
WARNING!
The battery pack contains nickel-cadmium, which is dangerous. It must therefore be handled with care.
Charge the battery pack prior to first use. The battery pack will have been shipped in a low charge state.
Use only the charger provided to charge the battery pack.
DO NOT
charge the battery pack when room temperature is below 10°C (50°F) or above 40°C (104°F).
DO NOT
attempt recharging the pack by means of an engine generator or a DC power source.
DO NOT
short-circuit the battery pack by touching both terminals at the same time with a metal object, or your fingers etc.
DO NOT
store battery pack (or wrench) in locations where the temperature may exceed 40°C (104°F) e.g. in outside sheds, above
heaters etc.
R
WARNING!
Dispose of spent battery pack correctly as it contains nickel-cadmium.
V
DANGER
!
DO NOT
attempt to disassemble the battery pack. For safety and environmental reasons
DO NOT
discard in domestic waste
or by burning. ONLY discard or recycle according to local authority regulations.
R
WARNING!
DO NOT
allow a leaking battery to contact your person. If you come into contact with battery liquid take the following
immediate action: a) Skin contact: Wash immediately with soap and water, then wash in either lemon juice or vinegar.
b) Eye contact: Wash with a strong solution of boric acid and seek immediate medical attention.
1.3.
MAINS POWER ELECTRICAL SAFETY
(In relation to the battery charger)
R
WARNING!
It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets
and any other connectors for wear or damage. You must ensure the risk of electric shock is minimised by the installation of
appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board.
We also recommend that a Residual Current Device (RCD) be used. It is particularly important to use an RCD with portable products that
Wear eye
Protection
Wear a mask
Wear ear
Protection
Refer to
Instruction
Manual
C
P2400.V4 | Issue 2(L) 15/04/15
Original Language Version
© Jack Sealey Limited
