OSCILLATING MULTI-TOOL - BODY ONLY
MODEL NO:
CP20VMT
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. GENERAL SAFETY.
9
Disconnect the multi-tool from the battery unit before changing accessories, servicing or performing any maintenance.
9
Maintain the multi-tool and battery in good condition. Check moving parts alignment on a regular basis.
9
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
9
Ensure the multi-tool is switched off before installing the battery pack.
9
Keep the multi-tool and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the multi-tool e.g. ceilings, floors and enclosures may contain electrical items or water piping.
9
Ensure battery pack is correctly inserted into the tool handle and latched in place before attempting to switch it on.
9
Secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
9
Keep children and unauthorised persons away from the working area.
9
Keep tool and charger in the case and store in a safe, dry, childproof area where the temperature will not exceed 104°F (40°C).
8
DO NOT
use the tool where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
DO NOT
allow children to operate the tool.
8
DO NOT
operate the tool if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT
hold unsecured work piece in your hand.
8
DO NOT
leave the tool operating unattended.
8
DO NOT
carry the tool with your finger on the power switch.
8
DO NOT
use the tool for a task it is not designed to perform.
8
DO NOT
operate the tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
get the tool or battery charger wet or use in damp or wet locations.
2.
i
INTRODUCTION
Comfortable composite housing with soft grip for added comfort. One tool suitable for multiple tasks such as sanding, scraping and
cutting various material. Built-in LED work light. Quick blade change system. Includes sanding paper, backing pad, plunge saw blade,
segment saw blade and scraper. Six speed settings. Requires Model No’s CP20VBP2, CP20VBP or CP20VBP4 20V Battery and Mains
Charger Model No. CP20VMC.
3.
i
SPECIFICATION
Model No: .............................................................CP20VMT
No Load Speed: ....................................... 5000 - 20000 RPM
Noise Power.................................................................108dB
Noise Pressure ..............................................................97dB
Vibration ............................................................... 15.258m/s
2
Uncertainty ................................................................. 1.5m/s
2
Weight: ........................................................................ 1.04kg
Consumables:
Battery: .............................20V 2Ah-4Ah Li-ion (not included)
2Ah Battery .......................................................... CP20VBP2
3Ah Battery ............................................................ CP20VBP
4Ah Battery .......................................................... CP20VBP4
Mains charger ....................................................... CP20VMC
Accessories:
Sanding Pads ................................................... CP20VMT.28
CP20VMT Issue 2 (2) 08/05/18
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Wear eye
protection
Wear a
mask
Wear ear
protection
Wear protective
gloves
