10.8V 3/8”SQ DRIVE CORDLESS RATCHET
WRENCH - BODY ONLY
MODEL NO:
CP108VCRWBO
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
9
Maintain the Ratchet Wrench and battery in good condition. Check moving parts alignment on a regular basis.
9
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
9
Ensure the Ratchet Wrench is switched off before installing the battery pack.
9
Keep the Ratchet Wrench and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the Ratchet Wrench; e.g. ceilings, floors and enclosures may contain electrical items or
water piping
9
Ensure battery pack is correctly inserted into the Ratchet Wrench handle and latched in place before attempting to switch on
Ratchet Wrench.
9
Secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
9
Be aware that this Ratchet Wrench does not need to be plugged into the mains power.
9
Keep children and unauthorised persons away from the working area.
8
DO NOT
use the Ratchet Wrench where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
DO NOT
allow children to operate the Ratchet Wrench.
8
DO NOT
operate the Ratchet Wrench
if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT
hold unsecured work piece in your hand.
8
DO NOT
leave the Ratchet Wrench operating unattended.
8
DO NOT
carry the Ratchet Wrench
with your finger on the power switch. Keep chuck direction switch in the locked position.
8
DO NOT
use the Ratchet Wrench
for a task it is not designed to perform.
8
DO NOT
operate the Ratchet Wrench
when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
get the Ratchet Wrench or battery charger wet or use in damp or wet locations.
1. INTRODUCTION
C
ompact, lightweight cordless ratchet wrench allows access to tight spaces. With spindle locking that gives more control during application and
a quick stopping function. Steel ratchet head with forward and reverse control. Robust housing with soft, comfortable grip. Body only. Requires
compatible 10.8V 2Ah or 4Ah battery and mains charger, sold separately.
2. SPECIFICATION
Model No.. .................................................. CP108VCRWBO
Battery ..................
10.8V 2Ah-4Ah Lithium-ion (not included)
C
onsumable parts (not included)
..........................................................CP108VBP 2Ah Battery
........................................................CP108VBP4 4Ah Battery
Drive ...........................................................................
3/8”sq.
M
ax. torque
......................................................
45Nm(33lb.ft)
N
oise power/noise pressure
.................................
91/80dB(A)
N
o-load speed
.........................................................
0-300rpm
Replacement parts .....................
CP108VMC - mains charger
V
ibration/uncertainty
..................................
11.64m/s²/1.5m/s²
3. OPERATION
3.1.
Fit battery.
3.2.
BATTERY CHARGE STATUS TEST
3.2.1.
Press trigger, all LEDs lit: battery charged, one LED lit: battery needs charging.
3.3.
In order to maintain battery efficiency:
DO NOT
fully discharge. After every use fully charge the battery, charge every 4 months even if tool is not used.
If a decrease of performance of the tool is noticed, charge the battery.
3.4.
Fit the socket to the wrench by snapping it onto the square drive.
C
P108VCRWBO Issue 1 02/02/21
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear ear
protection
Wear a mask
