background image

BOTTLE JACK  

10TONNE LOW ENTRY TELESCOPIC 

MODEL NO: 

BJ10LE

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these 

instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  SAFETY

9

9

9

Inspect and lubricate the jack regularly to ensure it is in good working order. 

DO NOT

 use the jack if damaged or a fault is suspected.    

Check chapter 6 troubleshooting. If necessary, repair or replace damaged parts immediately. 

9

9

9

Use authorised parts only, the use of unauthorised parts may be dangerous and will invalidate your warranty.

9

9

9

Ensure the jacking area is clean and tidy and free from unrelated materials and there is adequate lighting.  

9

9

9

Use jack on level and solid ground, preferably concrete. 

Avoid tarmacadam since the jack may sink in

.

9

9

9

Park the vehicle and apply hand brake; if automatic, place in Park (P) mode. Switch off the engine, and place chocks under the wheels.

9

9

9

Ensure minimum distance of 0.5m between vehicle tilt and static objects such as doors, walls, etc. 

9

9

9

Ensure all persons are out of the vehicle before jacking. 

DO NOT

 enter vehicle whilst it is supported on the jack or axle stands.

9

9

9

Check vehicle weight and recommended lifting points by referring to the vehicle owner’s manual. Ensure the lifting point is not corroded.

9

9

9

Check jack saddle is centred and stable on lifting point, (off-centre loads can slip). Position jack to avoid operating it from under vehicle.

9

9

DANGER! 

Use the jack for lifting only,

 NOT 

for supporting the lifted load. ALWAYS USE PROPERLY RATED AXLE STANDS. 

9

9

9

Keep hands etc. clear of moving parts during raising and lowering of the vehicle.

9

9

9

Use properly rated axle stands under the vehicle before proceeding with any task.

9

9

DANGER! 

Roadside wheel change is hazardous. 

Be extra vigilant. 

You may not be able to avoid jacking on tarmacadam. Get everyone 

   

out of vehicle. 

NEVER

 go under vehicle, traffic may cause vehicle to rock. Use hazard warning lights. If in doubt call professional help.

9

9

9

When changing a  wheel, slightly loosen wheel nuts prior to jacking vehicle. Screw wheel nuts back before lowering vehicle. 

9

9

9

Use a competent person to lubricate and maintain the jack. 

9

8

9

DO NOT

 exceed the rated capacity of the jack, and

9

DO NOT

 operate the jack beyond its maximum pump stroke. 

9

‰

9

WARNING! 

DO NOT 

allow the vehicle to move during jacking. 

DO NOT 

start the engine when vehicle is jacked up.

9

8

9

DO NOT

 jack a vehicle if it may result in the spillage of fuel, battery acid, or other dangerous substances. 

9

8

9

DO NOT

 place any part of your body under vehicle whilst supported by jack. Wait until properly rated axle stands have been correctly    

positioned.

9

8

9

DO NOT

 use jack to support extensions or cradles. 

DO NOT

 modify jack in any way. 

DO NOT

 use the jack for any other purpose than 

that for which it is designed.

9

8

9

DO NOT

 top up jack hydraulic system with brake fluid. Use hydraulic oil only, and 

DO NOT

 adjust the safety overload valve.

9

9

9

Ensure there are no persons or obstruction beneath the vehicle before lowering.

9

9

9

Clean, and stow the jack securely, with the ram in the down position. Ensure stowage area is dry.

9

‰

9

WARNING!

 

Remember,

 

It is 

very dangerous

 to get under a vehicle supported by a jack 

even

 if additional supports are used.  

 

8

 

DO NOT

 go under a vehicle without the support of properly rated axle stands. 

 NOTE:

 Seek advice before jacking caravans or trailers. 

2.  INTRODUCTION

Fitted with overload valve. Base and reservoir machine welded 

for increased strength and reduced chance of leakage. Threaded 

pump assembly allows for easy disassembly and maintenance. 

Supplied with 4pc handle. Fitted with carrying handle. Service kit 

readily available.

IMPORTANT SAFETY WARNING: ALWAYS USE AXLE STANDS

Please remember a jack is a lifting device and is not designed to 

support a load. Never get underneath a vehicle supported only 

by a jack - your life is at risk. We stock a comprehensive range of 

axle stands - please see relative section for full details.

3.  SPECIFICATION

Model No:

  . . . . . . . . . . . . . . . . . . . . . . . . . . .

BJ10LE

Capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Tonne

Minimum Height:. . . . . . . . . . . . . . . . . . . . . . . .128mm

Maximum Height: . . . . . . . . . . . . . . . . . . . . . . .223mm

Hydraulic Lift:  . . . . . . . . . . . . . . . . . . . . . . . . . . .95mm

Screw Extension:  . . . . . . . . . . . . . . . . . . . . . . . . . . N/A

  

BJ10LE   Issue: 2 (H,F, 2) - 10/06/19

Original Language Version

© Jack Sealey Limited

Refer to 

instructions

Отзывы: