InstructIons for:
mobile tool & parts trolley red/black
MoDEL no:
AP705M, AP705MB
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
2. INTRODUCTION & SPECIFICATION
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
3. CONTENTS
1.1
GENERAL SAFETY
WARNING!
Ensure Health & Safety, local authority, and general
workshop practice regulations are adhered to when using this
trolley.
WARNING!
be careful to ensure that when closing the sliding top
you do not catch any part of your body between the runners.
Always load evenly with the centre of gravity of the load as near
centre of the trolley as possible.
Keep the work area clean, uncluttered and ensure there is
adequate lighting.
Keep the trolley clean and tidy in accordance with good workshop
practice.
use the wheel locks to prevent the trolley from inadvertently
moving.
Keep children and unauthorised persons away from the work
area.
DO NOT
overload the trolley.
Max capacity 100kg
DO NOT
use the trolley
for any purpose other than that for which
it is designed.
DO NOT
stand on the trolley, use it as a ladder or allow others to
ride on the trolley.
DO NOT
leave unattended, especially when loaded, unless the
wheels are locked, chocked or the trolley is otherwise secured.
DO NOT
use trolley on uneven ground and do not run over curbs
or steps - use a ramp.
DO NOT
use trolley if any part is significantly damaged, paying
particular attention to the wheels.
Note! Do not force side drawers open, they will open only
when the sliding top is open.
Note! The assembly will require assistance.
3.1
carefully unpack the product and check the contents.
ITEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .QUANTITY
A) upper tray with 2 rubber mats. . . . . . . . . . . . . . . . . . . . . . . . . . .1
B) Legs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
c) Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
D) Bottom tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
E) rigid wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
f) swivel, locking castor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
G) Bolt M6 x 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
H) nut M12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Heavy gauge steel construction with lockable sliding top on smooth
ball bearing runners. twin drawers with 35mm ball bearing slides,
which are locked when top is closed. two fixed wheels and two
locking castors. suitable for tools and parts. some self-assembly
required.
size (H x W x L) . . . . . . . . . . . . . . . . . . . . . . . . .830 x 370 x 770mm
total load capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100kg
fig.1
Original Language Version
AP705M, AP705MB Issue:1 - 25/06/10
fig.2
