LAZY TONGS RIVETER
MODEL NO:
AK39902.V3
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING!
Ensure health & safety, local authority, and general workshop practice regulations are adhered to when using
this equipment.
9
Familiarise yourself with application and limitations, as well as the specific potential hazards peculiar to the riveter.
9
Replace or repair damaged parts. Use genuine parts only. Non authorised parts may be dangerous and will invalidate the warranty.
9
Keep the riveter clean for best and safest performance.
9
Locate riveter in an adequate working area for its function, keep area clean & tidy and free from unrelated materials and ensure there
is adequate lighting.
9
Keep children and unauthorised persons away from the working area.
9
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain and/ or tie back long hair.
WARNING!
Always wear approved eye or face protection when operating the riveter.
9
Keep fingers, hands and body clear of all working parts and
DO NOT
place any items within the riveter lattice.
9
Familiarise yourself with the push action to ensure you
DO NOT
accidentally wrench your wrist when pushing sharply.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.
9
Secure non stable work piece with a clamp, vice or other adequate holding device.
9
Ensure that all used rivet ends are disposed of in a safe manner.
8
DO NOT
get the riveter wet or use in wet locations.
8
DO NOT
use the riveter for any purpose other than for which it is designed.
8
DO NOT
operate the riveter when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
allow untrained persons to operate the riveter.
8
DO NOT
operate the riveter if any parts are damaged or missing as this may cause failure or possible personal injury.
2. INTRODUCTION
A
luminium head with steel jaw case and Chrome Molybdenum jaws for aluminium, steel and stainless steel rivets. Suitable for repetitive riveting
tasks. Supplied with five nozzles.
3. SPECIFICATION
Model No.: ......................................................... AK39902.V3
N
ozzles:
................................................................................
.
3.2mm(1/8”), 4mm(5/32”), 4.8mm(3/16”), 6mm, 6.4mm(1/4”)
Length: .......................................................................
800mm
R
ivet Types:
...........................................................................
............ Aluminium - Yes, Stainless Steel-Yes, Structural - No
4. OPERATION
4.1.
NOZZLES
4.1.1.
Select the appropriate nozzle.
4.1.2.
To remove nozzle at head, use suitable wrench. Ensure the replacement nozzle is completely screwed in and lightly
tighten with wrench.
4.2.
TO OPERATE
4.2.1.
Hold the head and pull the handle so that the lattice is completely extended.
WARNING!
Ensure your fingers are clear of moving parts. Insert rivet shaft all the way into the nozzle.
4.2.2.
Insert rivet head completely into the prepared work piece hole.
4.2.3.
Hold the riveter firmly and push on the handle to completely close the lattice which will fix the rivet in place and cut the shaft. Should
riveting not be achieved on the first try then re-extend the lattice and push once more.
4.2.4.
Once completed, pull the handle to extend the lattice again to eject the shaft end from the nozzle. Safely discard of shaft ends.
A
K39902.V3 Issue 2 (2) 14/12/21
Original Language Version
© Jack Sealey Limited
Refer to
instructions
fig.1
Wear eye
protection
Crushing of
hands
